ABB运动控制UNC4611B V2 HIER460378R3的操作

选项模块的功能包括：

•使用Operating（操作）按钮选择的适配器或抽头操作模式模式跳线（J4）。在适配器模式（默认）下，选项模块作为支持星形、线性或设备级环（DLR）网络拓扑。仅适用于Tap模式与PowerFlex 755驱动器一起使用时，选项模块使用ENET3（DEVICE）端口作为连接点，用于传输“Integrated Motion on”EtherNet/IP网络数据到PowerFlex 755驱动器的嵌入式EtherNet/IP适配器。

•工业以太网交换机和ENET1和ENET2网络端口为EtherNet/IP星形、线性或设备级环提供连接（DLR）网络拓扑。

•ENET3（设备）端口，仅适用于支持传输“EtherNet/IP网络上的Integrated Motion”该驱动器的数据。

•PowerFlex 750系列的嵌入式电子数据表（EDS）文件无需从Rockwell下载EDS文件的驱动器自动化网站。而是从选项上载EDS文件模块，使用RSLinx软件。

•自动设备配置（ADC），即“RSLogix 5000”软件，版本20或更高版本，功能“支持自动下载配置数据。这发生在Logix控制器之后建立与PowerFlex 750系列的EtherNet/IP网络连接驱动器（固件版本4.001或更高版本）及其相关外围设备。

•固定螺钉，用于将模块固定并接地至驱动器。

•开关，用于在接通电源之前设置网络节点地址或者您可以禁用交换机并使用BOOTP服务器动态主机配置协议（DHCP）服务器或选项模块参数配置IP地址。

•与配置选项的各种配置工具兼容模块和主机驱动器。这些工具包括增强的PowerFlex 7-Class驱动器上的HIM（目录号20-HIM-A6或20-HIM-C6S），以及驱动器配置软件，如DriveExplorer软件，版本6.01或更高版本，或DriveExecutive软件5.01或更高版。

•报告选项模块和网络状态的状态指示器表达当卸下驱动器盖时，它们是可见的。

•输入/输出中配置参数的32位数据链路，以满足应用要求（16个数据链路，用于将数据从网络写入驱动器，和16个数据链路，从驱动器向网络读取数据）。

•显式消息传递支持。

The features of the option module include the following: • Adapter or Tap mode of operation that is selected by using the Operating Mode Jumper ( J4). In Adapter mode (default), the option module operates as a network communication adapter supporting star, linear or device-level ring (DLR) network topologies. In Tap mode—only intended for use with PowerFlex 755 drives—the option module uses ENET3 (DEVICE) port as a connection point to transfer ‘Integrated Motion on the EtherNet/IP network’ data to the PowerFlex 755 drive’s embedded EtherNet/IP adapter. • Industrial Ethernet switch, and ENET1 and ENET2 network ports that provide connections for EtherNet/IP star, linear, or device-level ring (DLR) network topologies. • ENET3 (DEVICE) port—for use with only PowerFlex 755 drives—that supports the transfer of ‘Integrated Motion on the EtherNet/IP network’ data for that drive. • Embedded electronic data sheet (EDS) files for PowerFlex 750-Series drives that eliminate the need to download an EDS file from the Rockwell Automation website. Instead, the EDS file is uploaded from the option module by using RSLinx software. • Automatic Device Configuration (ADC), which is an ‘RSLogix 5000 software, version 20 or later, feature’ that supports the automatic download of configuration data. This occurs after the Logix controller establishes an EtherNet/IP network connection to a PowerFlex 750-Series drive (firmware revision 4.001 or later) and its associated peripherals. • Captive screws to secure and ground the module to the drive. • Switches to set a network node address before applying power to the drive—or you can disable the switches and use a BOOTP server, a Dynamic Host Configuration Protocol (DHCP) server, or option module parameters to configure the IP address. • Compatibility with various configuration tools to configure the option module and host drive. The tools include the enhanced PowerFlex 7-Class HIM (catalog number 20-HIM-A6 or 20-HIM-C6S) on the drive, and drive-configuration software, such as DriveExplorer software, version 6.01 or later, or DriveExecutive software, version 5.01 or later. • Status indicators that report the status of the option module and network communication. They are visible when the drive cover is removed. • Parameter-configured 32-bit Datalinks in the I/O to meet application requirements (16 Datalinks to write data from the network to the drive, and 16 Datalinks to read data to the network from the drive). • Explicit Messaging support.