88FN02B-E GJR2370800R0200机器人模块市场的进步空间

I/O映射用于指导不同I/O模块和逻辑程序。它是逻辑程序中使用的引用与I/O模块连接点。

I/O图还告诉控制器如何在用户逻辑和发送输出信号的位置。寄存器数据的格式（BCD二进制编码十进制或BIN二进制）。屏幕目标是加载卡选择和参考号选择以完成I/O的配置。

在Configuration Overview（配置概览）屏幕中，I/O掉线数和I/O模块数必须指定。输入I/O Map屏幕时，会检查这些数字进行现场连接

将现场侧接线连接至现场连接器上的适当引脚。

端子可接受每点两条14-AWG尺寸的电线或一条12-AWG尺寸的电线。

注：

1.所有小电流输入模块都容易受到现场接线连接器的微动（磨损）腐蚀；这些模块包括模拟、D/A、A/D、TTL。音乐等（B873、B875、B846等）。

2.施耐德电气建议在连接器上涂抹NYOGEL 759G润滑剂，以防止微动。Modicon零件号为99-C759-x00。

3.连接本模块时，电气设备只能由合格人员进行维修全体人员

4.如果使用绞合线，请确保松动或突出的绞合线不会使另一股短路或接地终端。

5.施耐德电气建议您使用实心电线。

6.执行此步骤时，请参阅800系列模块手册中的相应章节安装相应的连接器类型。

J890或J892模块可用于提供984之间的下降接口可编程控制器和S908 remote上的800系列I/O远程下降I/O（RIO）网络。两个接口模块都有两种型号，其中一种型号带有单个F连接器用于RIO电缆连接，一个带有两个F连接器。

在里面此外，J892还包含两个支持ASCII输入/输出的半双工端口

该J890/J892接口设备都有一组DIP开关，位于模块背面。

这些交换机用于设置唯一的RIO网络地址用于接口将驻留的远程放置。必须在上设置投递地址接口模块，然后将其安装在I/O外壳中。

The I/O Map is used to direct 

the flow of data between the various I/O modules and the logic program. It is the tie between the references used in the logic program and the I/O module connection points. The I/O Map also tells the controller how to use an input signal in user logic and where to send an output signal. The format of register data (BCD binary coded decimal or BIN binary) is specified on the I/O Map screen. The screen objective is to load the card selections and reference number selections to complete the configuration of the I/O. In the Configuration Overview screen, the number of I/O drops and I/O modules must be specified. These numbers are checked when entries to the I/O Map screen are made This J890/J892 Interface devices both have a set of DIP switches located on the back of the module. These switches are used to set a unique RIO network address for the remote drop where the interface will reside. The drop address must be set on the Interface module before it is installed in the I/O housing.

Field Connection Connect field side 

wiring to proper pins on the field connector. Terminals accept either two 14-AWG size wires or one 12-AWG size wire per point. Note: 1. All low current input modules are susceptible to fretting (wear) corrosion of field wiring connectors; these modules include analog, D/A, A/D, TTL. Muxs, etc. (B873, B875, B846, etc.). 2. Schneider Electric recommends applying NYOGEL 759G lubricant to the connector to prevent fretting. Modicon part number is 99-C759-x00. 3. When making connections to this module, electrical equipment should be serviced only by qualified personnel. 4. If you are using stranded wire, ensure that loose or projecting strands do not short circuit or ground the other terminals. 5. Schneider Electric recommends that you use solid wire. 6. When performing this step, refer to the appropriate chapter in the manual of the 800 Series module you are installing for the appropriate connector type.A J890 or J892 module may be used to provide the drop interface between a 984 Programmable Controller and a remote drop of 800 Series I/O on an S908 Remote I/O (RIO) network. Both interface modules are available in two models - one with a single F connector for RIO cable connection and one with two F connectors. In addition, the J892 contains two half-duplex ports that will support ASCII input/output devices at the remote drop