WOODWARD 8200-1300调速器9907-164的升级型号
在以前的固件版本中，非致命应用程序的故障条目提供的错误（例如，引用超出范围）数字识别导致错误的逻辑块的信息。然而用户无法将数字信息与块的名称。
新固件包括前12个字符故障条目中的块名称。在5.00版或更高版本中，如果尝试下载C块
如果包含未定义的符号，则下载将失败。
机器版将在反馈区显示以下消息：错误8097：控制器错误–控制器中止了请求[0x05][0xFF]在5.00版之前，包含未定义符号的C块可以成功下载，但如果它们被执行，CPU将转换到停止/暂停模式。
（5.0版或更高版本）“设置输入缓冲功能”将始终分配一个包含2049字节的缓冲区。这比先前的PACSystems版本。
传输列表验证与不兼容版本2.0x CRE020
使用CPU固件版本2.0x生成的冗余传输列表或更早版本与3.80版及更高版本的传输不兼容列表。
运行2.0x版的冗余控制器不会能够与运行3.80版或更高版本的固件。
以下限制适用于PACSystems RX7i机架：
▪ 基本模块必须位于不低于插槽4的插槽中。
▪ 扩展器模块必须位于不高于插槽11的插槽中。
▪ 扩展器模块不得位于低于底座的插槽中单元由于这些限制，以及90-70模块占用PACSystems RX7i机架中有两个插槽，最多三个可以使用扩展器。
（插槽4中的基座，插槽6、8和中的扩展器10或插槽5中的底座，插槽7、9和11中的扩展器。）请注意这些限制不适用于串联模拟扩展模块90-70扩展机架。
Genius总线控制器限制以下限制适用于PACSystems RX7i中的GBC：▪ 最小CPU扫描时间将按所需时间进行选通GBC更新其输出并收集其输入+500微秒。
要获得较小的扫描时间，请使用SUSIO功能块或将GBC放置在具有非默认特征的扫描集中。
▪ 如果%W参考地址用于COMMREQ状态或返回数据，它必须在%W00001-%W65536范围内。
▪ 存储或清除包含两个GBC的硬件配置连接到同一Genius网络可能会导致设备丢失其中一个GBC的故障。这是由GBC清算引起的他们的SBA异步。用户可以安全地忽略损失设备故障
In previous firmware versions, the fault entry for a non-fatal application
fault (for example, reference-out-of-range) provided numeric
information to identify the logic block causing the error. However, the
user did not have a way to correlate the numeric information with the
name of the block. The new firmware includes the first 12 characters
of the block name in the fault entry.In Release 5.00 or later, if an attempt is made to download a C block
containing undefined symbols, the download will fail. Machine Edition
will display the following message in the Feedback Zone: Error 8097:
Controller Error – Controller aborted the request [0x05][0xFF]
Prior to Release 5.00, C blocks containing undefined symbols could be
successfully downloaded, but if they were executed the CPU would
transition to Stop/Halt mode.(Release 5.0 or later) The "Set Up Input Buffer Function" will always
allocate a buffer containing 2049 bytes. This is one byte more than
previous PACSystems releases.
Transfer list validation not compatible with
Release 2.0x CRE020
Redundant transfer lists generated using CPU Firmware release 2.0x
or earlier are not compatible with the release 3.80 and later transfer
lists. Redundant controllers that are running release 2.0x will not be
able to synchronize with controllers that are running release 3.80 or
later firmware.The following restrictions apply to Analog Expansion Modules in a
PACSystems RX7i rack:
▪ The base module must be in a slot no lower than Slot 4.
▪ The expander module must be in a slot no higher than Slot 11.
▪ No expander module may be in a slot lower than the base
module.
Because of these restrictions, and because the 90-70 modules occupy
two slots in the PACSystems RX7i rack, a maximum of three
expanders are possible. (Base in Slot 4, Expanders in Slots 6, 8, and
10 or Base in Slot 5, Expanders in Slots 7, 9, and 11.) Please note that
these restrictions do not apply to Analog Expansion Modules in Series
90-70 Expansion Racks.
Genius Bus Controller restrictions The following restrictions apply to GBCs in PACSystems RX7i:
▪ The minimum CPU sweep time will be gated by the time it takes
the GBC to refresh its outputs and collect its inputs + 500
microseconds. To obtain a smaller sweep time, use the SUSIO
function block or place the GBCs in a scan set that has nondefault characteristics.
▪ If a %W reference address is used for COMMREQ status or return
data, it must be in the range %W00001 - %W65536.
▪ Storing or clearing a hardware configuration containing two GBCs
attached to the same Genius network may cause a Loss of Device
fault for one of the GBCs. This is caused by the GBCs clearing
their SBAs asynchronously. The user can safely ignore the Loss
of Device fault.
