D685A1156U01电磁流量计，ABB如何使用
开箱说明注意：如果装运纸箱在收到后损坏将设备从装运箱中取出在场以及设备的检装箱单并确认所有物品均已存在。保存包装设备储存和重新装运的材料。启动程序概述下表列出了您之前需要做的事情你可以使用这个板，在哪里可以找到你需要的信息每个步骤。一定要阅读这整章，并阅读所有内容开始前的注意事项。
D685A1156U01电磁流量计硬件准备MVME147已经过工厂测试，出厂时配有工厂安装的跳线，配置为提供系统功能系统需要。该模块在以下情况下运行：工厂安装的跳线，但要选择所需的配置并确保MVME147的正确操作，某些选项可能需要修改。通过在上安装或拆卸跳线来选择选项以下标题：❏ ROM配置选择（J1、J2）❏ 系统控制器选择（J3）❏ 串行端口4时钟配置选择（J8、J9）ROM配置选择标题（J1、J2）MVME147支持各种尺寸的EPROM和EEPROM。四个32针ROM/PROM/EPROM/EEPROM插槽为模块上提供。它们被组织为两个银行，两个每个气缸组的插座。每对插座可以单独安装已配置。插座U22和U30形成气缸组1。插座U1和U15表2。这些组被配置为使用U22和U1包括偶数字节，U30和U15包括奇数字节调试器软件EPROM安装在插槽U22和U30中。注意，有几种不同的算法用于擦除/写入EEPROM设备取决于制造商MVME147仅支持这些与“静态RAM”兼容的设备擦除/写入机制，如Xicor X28256或X2864H。
The MVME712 hardware preparation is provided in separate
manuals. Refer to Related Documentation in Chapter 1.
Unpacking Instructions
Note If the shipping carton is damaged upon receipt, request
that the carrier's agent be present during unpacking
and inspection of the equipment.
Unpack the equipment from the shipping carton. Refer to the
packing list and verify that all items are present. Save the packing
material for storing and reshipping of the equipment. Overview of Start-up Procedure
The following list identifies the things you will need to do before
you can use this board, and where to find the information you need
to perform each step. Be sure to read this entire chapter and read all
Caution notes before beginning. Hardware Preparation
The MVME147 has been factory tested and is shipped with factoryinstalled jumpers configured to provide the system functions
required for a VMEbus system. The module is operational with the
factory-installed jumpers, but to select the desired configuration
and ensure proper operation of the MVME147, certain option
modifications may be necessary.
Options are selected by installing or removing jumpers on the
following headers:
❏ ROM configuration select (J1, J2)
❏ System controller select (J3)
❏ Serial port 4 clock configuration select (J8, J9)
ROM Configuration Select Headers (J1, J2)
The MVME147 supports various sizes of EPROMs and EEPROMs.
Four 32-pin ROM/PROM/EPROM/EEPROM sockets are
provided on the module. They are organized as two banks with two
sockets per bank. Each pair of sockets may be individually
configured. Sockets U22 and U30 form bank 1. Sockets U1 and U15
form bank 2.
The banks are configured as word ports to the MPU with U22 and
U1 comprising the even bytes and U30 and U15 the odd bytes.
