HARTING 09061487901模块卡件
1.产 品 详 情 资 料：
三个板载通信端口：–CN1+CN2（内置，10/100Mbit/s）以太网端口（IEEE 802.3u，10Base-T/100Base-Tx）。–用于维修工具的COM4（内置）串行端口（RS-232C）。•两个冗余控制链路-RCU控制链路和RCU数据链路-用于冗余配置。•安全数字（SD）卡插槽，支持SD卡加载应用程序和循环保存冷保留值。支持各种制造商的SD卡。内存•16 MB闪存PROM（固件存储）。•256 MB DDR2 SDRAM，带完整性检查。功耗15.8 W，典型值19.5 W（包括对ModuleBus和CEXBus的完全供电。电流消耗660 mA，典型值（最大值750 mA）（不包括对ModuleBus和CEX总线的供电）。电源输入连接器四针螺纹连接器L+、L-、SA和SB。电源要求输入指定为L+和L-24 V标称电压，在19.2 V DC和30 V DC之间变化。冗余电源状态输入指定为SA、SB的输入•最大输入电压30 V•高电平的最小输入电压15 V•低电平的最大输入电压8 V这些是状态输入，阈值电平是输入上逻辑“0”或“1”的限制，即不是电源故障限制。根据EN60529和IEC 529，储能器5 ms防护等级IP20。重量1.6 kg（带包装1.9 kg）尺寸W 200 x H 186 x D 102 mm（7.9 x 7.3 x 4.0 in）宽度沿DIN导轨测量，距墙深度和垂直高度，包括锁紧机构。
Three on-board communication ports: – CN1 + CN2 (built in, 10/100Mbit/s) Ethernet ports (IEEE 802.3u, 10 Base-T/100Base-Tx). – COM4 (built in) serial port (RS-232C) for service tool. • Two Redundancy Control Links — RCU Control Link and RCU Data Link — for use in redundant configuration. • Secure Digital (SD) card slot that supports the SD card for loading of application and for saving the cold retain values cyclically. The SD cards of various manufacturers are supported.Memory • 16 MB flash PROM (firmware storage). • 256 MB of DDR2 SDRAM with integrity check. Power Dissipation 15.8 W typical 19.5 W typical (incl. full supply to ModuleBus and CEXBus. Current Consumption 660 mA typical (750 mA max.) (excl. supply of ModuleBus and CEX-Bus). Power Input Connector Four pin, screw connector L+, L–, SA and SB. Power Supply Requirements Inputs designated L+ and L– 24 V nominal, variation between 19.2 V DC and 30 V DC. Redundant Power Supply Status Inputs Inputs designated SA, SB • Max input voltage 30 V • Min. input voltage for high level 15 V • Max input voltage for low level 8 V These are status inputs and the threshold levels are limits for logic "0" or "1" on the inputs, that is, not power fail limits. Power Reservoir 5 ms Protection Rating IP20 according to EN60529, IEC 529. Weight 1.6 kg (1.9 kg with package) Dimensions W 200 x H 186 x D 102 mm (7.9 x 7.3 x 4.0 in) Width is measured along the DIN-rail, depth from the wall, and height vertically, including lock mechanism.
2.产 品 展 示
3.公 司 优 势 主 营 产 品
4.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
