ABB 88FV01E GJR2332300R0200自动化控制模块
1.产 品 详 情 资 料：
R（un）和F（ault）指示灯均不亮。ABB 88FV01E GJR2332300R0200装置正在配置中。请留出时间以便最终确定。如果这种情况持续存在，并且CEX总线上没有其他单元LED点亮：•检查是否将包括ABB 88FV01E GJR2332300R0200在内的有效硬件配置下载到控制器。•检查PM8xx处理器单元内的CEX总线保险丝。•从PM8xx处理器单元启动复位信号（INIT）。•更换ABB 88FV01E GJR2332300R0200装置。故障指示灯亮起ABB 88FV01E GJR2332300R0200装置正在重新启动过程中。请留出时间以便最终确定。如果情况依然存在，请更换单元。RxTx1/RxTx2 LED熄灭，各以太网信道无接收或发送活动。RxTx1/RxTx2 LED闪烁各个以太网信道的接收或发送活动正常。PRIM在非冗余模式下关闭：•此模块不是由应用程序启动的。在冗余模式下：•此模块不是由应用程序启动的，或者此模块充当备份接口。在非冗余模式下，RIM处于ON（打开）状态：•此模件由应用程序起动。在冗余模式下：•此模块由应用程序启动，此模块充当主接口。DUAL（双重）在非冗余模式下为OFF（关闭）：•非冗余模式时始终为OFF（断开）。在冗余模式下：•此模块未同步或此冗余对中的其他模块未启动。DUAL在非冗余模式下开启：•N/A在冗余模式下：•此模块未同步或此冗余对中的其他模块未启动。
Neither R(un) nor F(ault) LED's are ON The ABB 88FV01E GJR2332300R0200 unit is in the process of being configured. Allow time for this to finalize. If the condition persist, and no other unit LED on the CEX-Bus is lit: • Check that a valid HW configuration including the ABB 88FV01E GJR2332300R0200 is downloaded to the controller. • Check the CEX-Bus fuse inside the PM8xx processor unit. • Initiate a reset signal (INIT) from the PM8xx processor unit. • Replace the ABB 88FV01E GJR2332300R0200 unit. F(ault) LED is ON The ABB 88FV01E GJR2332300R0200 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. RxTx1/RxTx2 LED is OFF No Receive or transmit activity for respective Ethernet channels. RxTx1/RxTx2 LED is flashing Receive or transmit activity for respective Ethernet channels is normal. PRIM is OFF In non-redundant mode: • This module is not started by the application. In redundant mode: • This module is not started by the application or this module act as backup interface.PRIM is ON In non-redundant mode: • This module is started by the application. In redundant mode: • This module is started by the application and this module act as the primary interface. DUAL is OFF In non-redundant mode: • This is always OFF in non-redundant mode. In redundant mode: • This module is not synchronized or the other module in this redundant pair is not started. DUAL is ON In non-redundant mode: • N/A In redundant mode: • This module is not synchronized or the other module in this redundant pair is not started.
2.产 品 展 示
3.公 司 优 势 主 营 产 品
4.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
