NI PXI-2532开关模块
1.产 品 介 绍
品牌：NI
型号说明：NI PXI-2532开关模块
优势：供应进口原装正品，专业停产配件。
公司主营特点：主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。
2.产 品 详 情 资 料：
安装S100 I/O接口NI PXI-2532由处理器单元通过CEX总线供电，因此不需要额外的外部电源。使用以下步骤安装CI856/TP856:1。将装置安装在DIN导轨上，请参见第65页的“将AC 800M装置安装到DIN导轨上”和第78页的“以单一配置安装NI PXI-2532处理器装置”。2.将S100 I/O电缆TK575/TK580连接至基板上的触点。必须使用总线扩展器DSBC174/DSBC176/DSBC173A。S100 I/O连接和安装将S100 I/O机架电缆TK575/TK580连接到NI PXI-2532上的“I/O标记”36针中心线微型带状连接器。S100 I/O的安装有关S100 I/O相关组件的安装，请参阅S100 I/O文档。请注意，CI856单元没有单元冗余。安装INSUM接口NI PXI-2532由处理器单元通过CEX总线供电，因此不需要额外的外部电源。使用以下步骤安装NI PXI-2532。将装置安装到DIN导轨上，请参阅第65页的“将AC 800M装置安装在DIN导轨上”和“以单一配置安装NI PXI-2532处理器装置”
Installing the S100 I/O Interface, NI PXI-2532is powered from the processor unit via the CEX-Bus and requires therefore no additional external power source. Use the following procedure to install the CI856/TP856: 1. Mount the unit on the DIN-rail, see Mounting AC 800M Units onto DIN-Rail on page 65 and Installing the PM86x/TP830 Processor Unit in Single Configuration on page 78. 2. Connect the S100 I/O cable, TK575/TK580, to the contact on the baseplate. A bus extender, DSBC174/DSBC176/DSBC173A, must be used. S100 I/O Connection and Installation Connect the S100 I/O rack cable NI PXI-2532 to the “I/O-labeled” 36-pin centerline miniature ribbon connector located on TP856. Installation of S100 I/O For installation of the S100 I/O-related components, see S100 I/O documentation. Note that there is no unit redundancy for the NI PXI-2532 unit.Installing the INSUM Interface, NI PXI-2532The CI857 is powered from the processor unit via the CEX-Bus and requires therefore no additional external power source. Use the following procedure to install the CI857/TP853: 1. Mount the unit onto the DIN-rail, see Mounting AC 800M Units onto DIN-Rail on page 65 and Installing the PM86x/TP830 Processor Unit in Single Configuration
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
