WOODWARD 5466-340控制器
1.产 品 介 绍
品牌：WOODWARD
型号说明：WOODWARD 5466-340控制器
优势：供应进口原装正品，专业停产配件。
公司主营特点：主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。
2.产 品 详 情 资 料：
WOODWARD 5466-340使用以下步骤沿DIN导轨安装处理器单元：1。如果已安装，请从处理器单元侧面卸下CEX总线和ModuleBus终端。2.安装处理器单元、通信接口和S800 I/O单元。所有PM8xx的通信接口位于处理器单元左侧的CEX总线上。WOODWARD 5466-340 I/O单元位于处理器单元右侧的电气模块总线上。3.轻轻地将它们压在一起，确保ModuleBus和CEXBus通过基板连接器正确连接。4.将总线终端重新插入距离处理器单元最远的通信单元。a.对于CEX总线TB850（如果使用电缆TK850，则为TB851），请参见第80页图25和第81页图26。使用BC810时，请参见第82页的图27。如果CEX总线上未使用任何单元，则不需要总线终端。b.对于ModuleBus TB807，请参阅S800 I/O文档。如果ModuleBus上未使用任何单元，则不需要总线终端。本主题不适用于PM891处理器单元。请参阅第87页的“以单一配置安装PM891”。对于PM861/PM864/PM865/PM866，在RCU链路连接器处插入RCU链路终端插头TB852。当以单一配置运行时，终端插头必须始终用于WOODWARD 5466-340。当冗余处理器以单一配置运行时，如果RCU链路终端插头TB852不可用，则使用RCU链路电缆TK851。
Use the procedure below to install the processor unit along the DIN-rail: 1. If already mounted, remove the CEX-Bus and ModuleBus terminations from the sides of the processor unit. 2. Mount the processor unit, the communication interfaces, and theWOODWARD 5466-340 I/O units. The communication interfaces for all PM8xx is on the CEX-Bus to the left of the processor unit. The S800 I/O units for PM8xx is on the electrical ModuleBus to the right of the processor unit. 3. Press them gently together and make sure that the ModuleBus and the CEXBus are correctly connected, via baseplate connectors. 4. Reinsert the bus terminations into the communication units at farthest away from the processor unit. a. For CEX-Bus TB850 (TB851 if cable TK850 is used), see Figure 25 on page 80 and Figure 26 on page 81. When using BC810, see Figure 27 on page 82. If no units are used on the CEX-Bus, no bus termination is required. b. For ModuleBus TB807, refer to the S800 I/O documentation. If no units are used on the ModuleBus, no bus termination is required. This topic does not apply to the PM891 processor unit. See Installing PM891 in Single Configuration on page 87. For PM861/PM864/PM865/PM866 insert the RCU Link Termination plug TB852, at the RCU Link connector. The termination plug must always be used for WOODWARD 5466-340 when running in single configuration. When a redundant processor is running in a single configuration use the RCU Link Cable TK851, if the RCU Link Termination plug TB852 is not available.
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
