REXROTH MSK060C-0600-NN-M1-UG0-NNNN伺服电机
1.产 品 介 绍
品牌：REXROTH
型号说明：REXROTH MSK060C-0600-NN-M1-UG0-NNNN伺服电机
优势：供应进口原装正品，专业停产配件。
公司主营特点：主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。
2.产 品 详 情 资 料：
REXROTH MSK060C-0600-NN-M1-UG0-NNNNMPAR地址指向的代码正在执行。ASCII P（HEX 50）——程序闪存。MPAR被设置为闪存程序控制包的地址。ASCII R（HEX 52）--就绪。固件监视器正在监视更改。您只能通过MPCR方法对闪存进行编程。有关闪存程序控制包结构的说明，请参阅Motorola 68K CISC CPU用户手册调试包中的.PFLASH系统调用。REXROTH MSK060C-0600-NN-M1-UG0-NNNN总线主机可以设置的状态代码是：使用Go Direct（GD）逻辑指定MPAR地址。ASCII B（HEX 42）——使用Go（G）逻辑安装断点。多处理器地址寄存器（MPAR）位于共享RAM位置，与调试器加载它的基地址偏移$804，包含用于控制处理器之间通信的两个长字中的第二个。如果MPCR包含G或B，MPAR内容指定远程处理器开始执行的地址。MPAR组织如下：通电时，调试监视器自检例程初始化RAM，包括用于多处理器支持的内存位置（800美元至807美元）。REXROTH MSK060C-0600-NN-M1-UG0-NNNN
Code pointed to by the MPAR address is executing. ASCII P (HEX 50) -- Program Flash Memory. The MPAR is set to the address of the Flash memory program control packet. ASCII R (HEX 52) -- Ready. The firmware monitor is watching for a change.You can only program flash memory by the MPCR method. Refer to the .PFLASH system call in the REXROTH MSK060C-0600-NN-M1-UG0-NNNNDebugging Package for Motorola 68K CISC CPUs User’s Manual for a description of the flash memory program control packet structure. The status codes that may be set by the bus master are:Use Go Direct (GD) logic specifying the MPAR address. ASCII B (HEX 42) -- Install breakpoints using the Go (G) logic.The Multiprocessor Address Register (MPAR), located in shared RAM location of $804 offset from the base address the debugger loads it at, contains the second of two longwords used to control communication between processors. The MPAR contents specify the address at which execution for the remote processor is to begin if the MPCR contains a G or B. The MPAR is organized as follows:At power-up, the debug monitor self-test routines initialize RAM, including the memory locations used for multi-processor support ($800 through $807).REXROTH MSK060C-0600-NN-M1-UG0-NNNN
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
