REXROTH MSK040C-0600-NN-M1-UG0-NNNN伺服电机
1.产 品 介 绍
品牌：REXROTH
型号说明：REXROTH MSK040C-0600-NN-M1-UG0-NNNN伺服电机
优势：供应进口原装正品，专业停产配件。
公司主营特点：主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。
2.产 品 详 情 资 料：
REXROTH MSK040C-0600-NN-M1-UG0-NNNN如果尝试的网络操作失败，则网络I/O错误代码162Bug将返回错误代码。多处理器支持MVME162FX控制器的双端口RAM功能使共享RAM可用于远程处理器和本地处理器。这可以通过以下两种方法之一完成。任何一种方法都可以通过ENV命令启用/禁用，作为其远程启动开关方法（参见第5章）。多处理器控制寄存器（MPCR）REXROTH MSK040C-0600-NN-M1-UG0-NNNN方法远程处理器可以通过使用多处理器控制暂存器（MPCR，Multiprocessor Control Register）发出远程GO命令，在本地MVME162FX双端口RAM中启动程序执行。MPCR位于共享RAM位置，与调试器加载它的基地址相距800美元，它包含用于控制处理器之间通信的两个长字之一。MPCR内容组织如下：MPCR中存储的状态代码有两种类型：❏ 返回的状态（从监视器）❏ 状态设置（由总线主机设置）监视器可能返回的状态代码为：等待。初始化尚未完成。REXROTH MSK040C-0600-NN-M1-UG0-NNNN
Network I/O Error Codes 162Bug returns an error code if an attempted network operation is unsuccessful. Multiprocessor REXROTH MSK040C-0600-NN-M1-UG0-NNNNSupport The MVME162FX controller’s dual-port RAM feature makes the shared RAM available to remote processors as well as to the local processor. This can be done by either of the following two methods. Either method can be enabled/disabled by the ENV command as its Remote Start Switch Method (refer to Chapter 5). Multiprocessor Control Register (MPCR) Method A remote processor can initiate program execution in the local MVME162FX dual-port RAM by issuing a remote GO command using the Multiprocessor Control Register (MPCR). The MPCR, located at shared RAM location of $800 offset from the base address the debugger loads it at, contains one of two longwords used to control communication between processors. The MPCR contents are organized as follows: The status codes stored in the MPCR are of two types: ❏ Status returned (from the monitor) ❏ Status set (by the bus master) The status codes that may be returned from the monitor are:Wait. Initialization not yet complete.REXROTH MSK040C-0600-NN-M1-UG0-NNNN
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
