57520001-DX/1 DSTC406通讯卡件
第1类建筑，a）被指定为A3、A4、F2、G1、H2、H3或H4类占用（参见SANS 10400-a中的A20条例），b）没有地下室，c）提供横向支撑的交叉墙或构件之间的最大长度为6.0 m，和d）建筑面积不超过80 m2。SANS 10400-a:2010的注释1表C.1概述了1类建筑和其他在许多建筑属性方面具有相同占用名称的建筑之间的性能差异。注2：就SANS 10400的一个或多个部分而言，建筑物可归类为1类建筑物。因此，可对第1类建筑物施加额外限制。例如，SANS 10400-T（消防）中的1类建筑将被限制为单层。注3：第1类建筑物的防火要求基于居住者迅速逃离建筑物。因此，不应超过《条例》A部分表2（见SANS 10400-A）中规定的居住设计人口。3.6合格人员——凭借其教育、培训、经验和背景知识，有资格就建筑或其部分的功能性法规性能做出决定，或承担国家建筑法规规定的职责的人员。注：这是一个通用定义，在未给出其他定义或未参考其他标准的情况下使用。SANS 10400的其他部分包含与其学科相关的更具体性质的定义。3.7合格人员（土木工程），a）根据2000年《工程职业法》（2000年第46号法案）注册为专业工程师或专业工程技术人员，b）具有土木工程专业资格（学位或文凭），以及category 1 building building which a) is designated as being of class A3, A4, F2, G1, H2, H3, or H4 occupancy (see Regulation A20 in SANS 10400-A), b) has no basements, c) has a maximum length of 6,0 m between intersecting walls or members providing lateral support, and d) has a floor area that does not exceed 80 m2 NOTE 1 Table C.1 of SANS 10400-A:2010 outlines the difference in performance between category 1 buildings and other buildings that have the same occupancy designation in respect of a number of building attributes. NOTE 2 A building may be classified as a category 1 building for the purposes of one or more parts of SANS 10400. Additional limitations may accordingly be imposed on category 1 buildings. For example, a category 1 building in terms of SANS 10400-T (Fire protection) will be restricted to a single storey. NOTE 3 Fire requirements for category 1 buildings are based on occupants escaping quickly from buildings. The design population for occupancies as set out in table 2 of part A of the Regulations (see SANS 10400-A) should therefore not be exceeded. 3.6 competent person person who is qualified by virtue of his education, training, experience and contextual knowledge to make a determination regarding the performance of a building or part thereof in relation to a functional regulation or to undertake such duties as may be assigned to him in terms of the National Building Regulations NOTE This is a generic definition, to be used where no other definition is given, or no references are made to other standards. Other parts of SANS 10400 contain definitions of a more specific nature relevant to their disciplines. 3.7 competent person (civil engineering) person who a) is registered in terms of the Engineering Profession Act, 2000 (Act No. 46 of 2000), as either a Professional Engineer or a Professional Engineering Technologist, b) has a tertiary qualification (degree or diploma) in civil engineering, and
