HDC01.1-A040N-IB01-01-FW机械设备卡件
在本设备的操作、维护和维修的所有阶段，必须遵守以下一般安全预防措施。未遵守这些预防措施或本手册其他地方的特定警告违反了设备设计、制造和预期用途的安全标准。对于客户未能遵守这些要求，股份有限公司不承担任何责任。下面列出的安全预防措施代表摩托罗拉意识到的某些危险的警告。作为本产品的用户，您应遵守这些警告以及在您的操作环境中安全操作设备所需的所有其他安全预防措施。将仪器接地。为了尽量减少电击危险，设备底盘和外壳必须连接到电气接地。设备配有三芯交流电源电缆。电源线必须插入经批准的三触点电源插座。电力电缆的电源插座和配合插头符合国际电工委员会（IEC）安全标准。请勿在爆炸性环境中操作。切勿在存在易燃气体或烟雾的情况下操作设备。在这样的环境中操作任何电气设备都会构成明确的安全隐患。远离带电电路。操作人员不得拆除设备盖。只有工厂授权维修人员或其他合格维修人员才能拆除设备盖，以进行内部组件或部件更换或任何内部调整。不要更换连接有电源线的部件。在某些情况下，即使拆除了电源电缆，也可能存在危险电压。为避免受伤，在接触电路之前，务必断开电源和放电电路。请勿单独维修或调整。除非有其他能够提供急救和复苏的人员在场，否则不要尝试内部服务或调整。暴露或处理CRT时应小心。阴极射线管（CRT）的破裂导致玻璃碎片的高速散射（内爆）。为了防止CRT内爆，避免粗暴操作或设备震动。CRT的操作只能由合格的维护人员使用经批准的安全面罩和手套进行。不得更换零件或修改设备。由于存在引入额外危险的危险，请勿安装替代部件或对设备进行任何未经授权的修改。请联系您当地的摩托罗拉代表进行维修，以确保安全功能得到维护。危险程序警告。在本手册中，警告（如以下示例）位于潜在危险程序之前。必须遵守警告中的说明。您还应采取您认为在您的操作环境中操作设备所必需的所有其他安全预防措施！警告：本设备中存在可能导致死亡的危险电压。在处理、测试和调整时要格外小心。所有摩托罗拉PWB（印刷电路板）均由UL认可的制造商制造，可燃性等级为94V-0！警告：本设备产生、使用并辐射电磁能。如果未在具有足够EMI保护的机柜中安装和使用，可能会导致或易受电磁干扰（EMI）的影响。p欧洲通知：带有CE标志的电路板产品符合EMC指令（89/336/EEC）。符合本指令意味着符合以下欧洲规范：EN55022（CISPR 22）无线电
s On You The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the equipment. Motorola, Inc. assumes no liability for the customer’s failure to comply with these requirements. The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the user of the product, should follow these warnings and all other safety precautions necessary for the safe operation of the equipment in your operating environment. Ground the Instrument. To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground. The equipment is supplied with a three-conductor AC power cable. The power cable must be plugged into an approved three-contact electrical outlet. The power jack and mating plug of the power cable meet International Electrotechnical Commission (IEC) safety standards. Do Not Operate in an Explosive Atmosphere. Do not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard. Keep Away From Live Circuits. Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or other qualified maintenance personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment. Do not replace components with power cable connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To avoid injuries, always disconnect power and discharge circuits before touching them. Do Not Service or Adjust Alone. Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is present. Use Caution When Exposing or Handling the CRT. Breakage of the Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion). To prevent CRT implosion, avoid rough handling or jarring of the equipment. Handling of the CRT should be done only by qualified maintenance personnel using approved safety mask and gloves. Do Not Substitute Parts or Modify Equipment. Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification of the equipment. Contact your local Motorola representative for service and repair to ensure that safety features are maintained. Dangerous Procedure Warnings. Warnings, such as the example below, precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed. You should also employ all other safety precautions which you deem necessary for the operation of the equipment in your operating environment. ! WARNING Dangerous voltages, capable of causing death, are present in this equipment. Use extreme caution when handling, testing, and adjusting. All Motorola PWBs (printed wiring boards) are manufactured by UL-recognized manufacturers, with a flammability rating of 94V-0. ! WARNING This equipment generates, uses, and can radiate electromagnetic energy. It may cause or be susceptible to electromagnetic interference (EMI) if not installed and used in a cabinet with adequate EMI protection. p European notice: Board products with the CE marking comply with the EMC Directive (89/336/EEC). Compliance with this directive implies conformity to the following European norms: EN55022 (CISPR 22) Radio
