HIEE205014R1通用电气卡件
f必须通过向WinLoader实用程序指定模块的机架和插槽位置来明确升级固件。CPE330、CPE400、CPL410和CPE100/CPE115的固件升级通过以太网使用web浏览器执行。此方法提供了增强的安全功能。该程序的说明包含在相应的升级工具包文档中。WinLoader实用程序无法与CPE330、CPE400、CPL410或CPE100/CPE115 CPU一起使用。1.3.7 SRTP客户端（信道）SRTP客户端允许PACSystems PLC启动与网络上其他支持SRTP的设备的数据传输。SRTP通道可在PLC应用程序中设置。SRTP支持COMMREQ驱动的信道命令，以建立新信道、中止现有信道、在现有信道上传输数据以及检索现有信道的状态。任何给定信道一次只能分配给一个协议。有关支持的信道数量和组合，请参阅第1.3.3节PACSystems控制器的以太网接口。1.3.8 Modbus TCP客户端（通道）Modbus TCP客户端允许PACSystems PLC启动与网络上其他Modbus TCP服务器设备的数据传输。Modbus TCP信道可在应用程序中设置。Modbus TCP客户端支持COMMREQ驱动的信道命令，以打开新信道、关闭现有信道和在现有信道上传输数据。任何给定信道一次只能分配给一个协议。有关支持的信道数量和组合，请参阅第1.3节PACSystems控制器的以太网接口。PAC系统™ RX3i和RSTi EP TCP/IP以太网通信用户手册第1节GFK-2224Y 2019年8月简介13 1.3.9以太网全球数据（EGD）▪ EGD类：•EGD类1配置为无EGD操作逻辑控制的交换。o CPE302/CPE305/CPE310/CPE330/CPE400/CPE410/CPE100/CPE115中支持？EGD Class 2是EGD命令，是使用COMMREQ的逻辑驱动EGD交换。o在IC695ETM001上受支持o在发布时CPE302/CPE305/CPE310/CPE330/CPE400/CPE410/CPE100/CPE115的嵌入式以太网端口上不受支持每个PACSystems RX3i CPU最多支持255个1级同时EGD交换，RSTi EP CPU CPE100/CPE115最多支持8个1级同步EGD交换。EGD交换机使用编程器进行配置，并存储在PLC中。可以配置生产和消费交换。PACSystems以太网接口支持EGD交换机的选择性消费和EGD交换机生产以及本地子网广播IP地址的消费。注意：对于广播寻址，不支持子网值0.0.0.0。1.3.9.1将EGD时间戳与SNTP同步ETM001 Jx和-Kxxx以太网接口均可配置为使用简单网络时间协议（SNTP）来同步生成的EGD交换的时间戳。通过适当的PME硬件配置，CPE302、CPE305、CPE310、CPE330、CPE400和CPL410上的嵌入式以太网接口也将支持SNTP。有关PME硬件配置的更多信息，请参阅第4.1.3节“配置以太网接口参数”。注：RSTi EP CPE100/CPE115不支持SNTP。以太网接口模块SNTP支持ETM001 Jx是，具有PME硬件配置（不使用AUP文件的默认配置）ETM001 Kxxx是，具有PM E硬件配置CPU SNTP支持CPL410是，具有PE E硬件配置PACSystems™ RX3i和RSTi EP TCP/IP以太网通信用户手册第1节GFK-2224Y
irmware must be explicitly upgraded by specifying the rack and slot location of the module to the WinLoader utility. Firmware upgrades for the CPE330, CPE400, CPL410 and CPE100/CPE115 are performed over Ethernet using a web browser. This method provides enhanced security features. Instructions for the procedure are included in the corresponding upgrade kit documentation. The WinLoader utility will not work with the CPE330, CPE400, CPL410 or CPE100/CPE115 CPUs. 1.3.7 SRTP Client (Channels) SRTP Client allows the PACSystems PLC to initiate data transfer with other SRTP-capable devices on the network. SRTP channels can be set up in the PLC application program. SRTP supports COMMREQ-driven channel commands to establish new channels, abort existing channels, transfer data on an existing channel, and retrieve the status of an existing channel. Any given channel can be assigned to only one protocol at a time. For the number and combinations of channels supported, refer to Section 1.3.3 Ethernet Interfaces for PACSystems Controllers. 1.3.8 Modbus TCP Client (Channels) Modbus TCP Client allows the PACSystems PLC to initiate data transfer with other Modbus TCP server devices on the network. Modbus TCP channels can be set up in the application program. The Modbus TCP Client supports COMMREQ-driven channel commands to open new channels, close existing channels, and transfer data on an existing channel. Any given channel can be assigned to only one protocol at a time. For the number and combinations of channels supported, refer to Section 1.3 Ethernet Interfaces for PACSystems Controllers. PACSystems™ RX3i and RSTi-EP TCP/IP Ethernet Communications User Manual Section 1 GFK-2224Y August 2019 Introduction 13 1.3.9 Ethernet Global Data (EGD) ▪ EGD Classes: • EGD Class 1 is configured exchanges with no logic control of EGD operation. o Supported in CPE302/CPE305/CPE310/CPE330/CPE400/CPL410/CPE100/CPE115 • EGD Class 2 is EGD Commands which are logic-driven EGD exchanges using COMMREQs. o Supported on IC695ETM001 o Not supported on embedded Ethernet ports of CPE302/CPE305/CPE310/CPE330/CPE400/CPL410/CPE100/CPE115 at time of publication Each PACSystems RX3i CPU supports up to 255 Class 1 simultaneous EGD exchanges and RSTi-EP CPU CPE100/CPE115 supports up to eight Class 1 simultaneous EGD exchanges. EGD exchanges are configured using the programmer and stored into the PLC. Both Produced and Consumed exchanges can be configured. PACSystems Ethernet interfaces support both selective consumption of EGD exchanges and EGD exchange production and consumption to the broadcast IP address of the local subnet. Note: For Broadcast addressing a Subnet value of 0.0.0.0 is NOT supported. 1.3.9.1 Synchronizing EGD Timestamps with SNTP Both the ETM001-Jx and -Kxxx Ethernet interfaces can be configured to use Simple Network Time Protocol (SNTP) to synchronize the timestamps of produced EGD exchanges. With an appropriate PME Hardware Configuration, the embedded Ethernet interface on the CPE302, CPE305, CPE310, CPE330, CPE400 and CPL410 will also support SNTP. For more information on PME Hardware Configuration, please refer to Section 4.1.3, Configuring the Ethernet Interface Parameters. Note: The RSTi-EP CPE100/CPE115 does not support SNTP. Ethernet interface module SNTP Support ETM001-Jx Yes, with PME Hardware Configuration (default configuration without using AUP file) ETM001-Kxxx Yes, with PME Hardware Configuration CPU SNTP Support CPL410 Yes, with PME Hardware Configuration PACSystems™ RX3i and RSTi-EP TCP/IP Ethernet Communications User Manual Section 1 GFK-2224Y
