HIEE300024R4工控自动化卡件
使用TBQC–接线板快速连接方法使用一对电缆，每端带有连接器。这些连接器从模块连接器连接到DIN导轨安装接线板上的连接器。TBQC组件见附录D.7 7-50系列90-30 PLC I/O模块规范–2000年7月GFK-0898F表7-24。IC693MDL753额定电压输出电压范围12至24伏DC的规范，每个模块隔离32的正逻辑10.2至28.8伏DC输出（四组，每组八个输出），场侧和逻辑侧之间1500伏，组间250伏输出电流每点0.5安培，每组最大4安培，每组公共引脚最大3安培输出特性浪涌电流5.4安培，持续10毫秒导通状态压降0.3伏DC关断状态泄漏电流0.1 mA最大开启响应时间0.5 ms最大关闭响应时间0.5毫秒最大内部功耗260 mA（最大），来自背板上的5伏总线；（13 mA+3 mA/点开+4.7 mA/LED）用户电源@24 VDC时每组16.5 mA（最大值），7 GFK-0898F第7章-离散输出模块7-51 IC693MDL753输出用户每组9.6 mA（最大），以帮助使用电缆IC693CBL315连接24针连接器。它在一个表中包含所有必需的接线信息。此表包含以下信息：模块点编号：A1-A8、B1-B8、C1-C8、D1-D8、电压和公共点连接器引脚编号：A1到A12，以及B1到B12电缆对编号：1对到12对导线颜色代码：基色或带有示踪色的基色也提供了电路参考和客户线号列。接线12/24伏直流、0.5A正逻辑、32点输出模块时，请根据需要复制并使用本页和下页的工作表。本出版物中使用的模块组A和B（模块右前方的连接器）通信用户手册警告和注意事项本出版物中的警告警告注意事项旨在强调本设备中存在危险电压、电流、温度或其他可能导致人身伤害的条件，或可能与其使用相关。如果不注意可能导致人身伤害或设备损坏，则使用警告通知。警告如果不小心，可能会损坏设备，请使用警告通知。注意：注意事项只会引起对理解和操作设备特别重要的信息的注意。这些说明并不旨在涵盖设备的所有细节或变化，也不旨在规定安装、操作和维护期间可能遇到的所有意外情况。本信息仅供参考，Emerson不对本文所含信息的准确性作出任何保证。定期对设备和规范进行更改、修改和/或改进，这些更改可能反映在本文中，也可能不反映在本文。据了解，Emerson可随时对此处引用的设备或文件本身进行更改、修改或改进。本文件适用于熟悉Emerson的训练有素的人员
Using a TBQC – The Terminal Block Quick Connect method uses a pair of cables with connectors on each end. These connect from the module connectors to connectors on DIN–rail mounted terminal blocks. The TBQC components are discussed in Appendix D. 7 7-50 Series 90-30 PLC I/O Module Specifications – July 2000 GFK-0898F Table 7-24. Specifications for IC693MDL753 Rated Voltage Output Voltage Range 12 through 24 volts DC, positive logic 10.2 to 28.8 volts DC Outputs per Module Isolation 32 (four groups of eight outputs each) 1500 volts between field side and logic side 250 volts between groups Output Current 0.5 amps per point with 4 amps maximum per group and 3 amps maximum per group common pin Output Characteristics Inrush Current 5.4 amps for 10 ms On-state Voltage Drop 0.3 volts DC Off-state Leakage Current 0.1 mA maximum On Response Time 0.5 ms maximum Off Response Time 0.5 ms maximum Internal Power Consumption 260 mA (maximum) from 5 volt bus on backplane; (13 mA + 3 mA/point ON + 4.7 mA/LED) 16.5 mA (maximum) per group from user supply @ 24 VDC and all eight outputs in group ON 9.6 mA (maximum) per group from 7 GFK-0898F Chapter 7 – Discrete Output Modules 7-51 IC693MDL753 Output customers as an aid to wiring the 24-pin connectors using cable IC693CBL315. It includes all of the required wiring information in one table. This table has the following information:module point number: A1 - A8, B1 - B8, C1 - C8, D1 - D8, voltage and common pointsconnector pin number: A1 through A12, and B1 through B12cable pair number: pair 1 through pair 12wire color code: base color or base color with tracer color Columns are also provided for circuit references and customer wire numbers. Please copy and use the work sheets on this and the following page as needed when wiring the 12/24 Volt DC, 0.5A Positive Logic, 32 Point Output module. Wiring for Module Groups A and B (connector on right front of module) Communications User Manual Warnings and Caution Notes as Used in this Publication WARNING Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. CAUTION Caution notices are used where equipment might be damaged if care is not taken. Note: Notes merely call attention to information that is especially significant to understanding and operating the equipment. These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency to be met during installation, operation, and maintenance. The information is supplied for informational purposes only, and Emerson makes no warranty as to the accuracy of the information included herein. Changes, modifications, and/or improvements to equipment and specifications are made periodically and these changes may or may not be reflected herein. It is understood that Emerson may make changes, modifications, or improvements to the equipment referenced herein or to the document itself at any time. This document is intended for trained personnel familiar with the Emerson
