HIEE300725R1工控备件机器人模块
17.1高密度模块安装接线板接线板类型目录号盒型接线板，36个端子IC694TBB032弹簧型接线板、36个端子IC 694TBS032扩展盒型接线端子、36个终端IC694TBB 132扩展弹簧型接线端子，36端子IC694TBS132 PACSystems*RX3i系统手册附录专用模块822 17.1.1高密度RX3i模块的端子块17.1.1.1扩展高密度与高密度端子块扩展高密度端子板IC694TBB132和IC694TBS 132在功能上与高密度接线板IC694 TB032和IC694 BS032相同。两者都直接连接到I/O模块。扩展高密度接线板的外盖深约13 mm（½in）。这是为了适应具有较厚绝缘的电线，例如通常用于AC I/O模块的电线。13mm（0.5英寸）扩展高密度接线板增加深度图422：扩展高密度端子板增加的深度图423比较了从模块底部看的高密度端子块（左侧）和扩展高密度终端块（右侧）上的布线空间。10mm（0.4英寸）23mm（0.9英寸）图423：深度比较：与大多数其他PACSystems和90-30系列PLC模块的深度相同。扩展接线板IC694TBB132带有一个比接线板IC6914TBB032深约13 mm（½英寸）的外盖，以容纳绝缘较厚的电线，例如通常用于交流输入/输出模块的电线。17.1.1.2.1规格：TBB032和TBB132扭矩0.79 Nm（7 in-lb）线带长度7.87 mm（0.310 in）线规支持#14-26 AWG（实心或绞合）17.1.1.2.2将现场接线连接到箱式高密度接线板接线板底部可用作线带长度的量规，如图425所示。剥开的电线必须完全插入接线盒，以使绝缘层与端子内部的停止位置相接，并且电线末端弯曲。拧紧端子螺钉，将电线抬起并夹紧到位。PACSystems*RX3i系统手册附录专用模块824导线带长度将导线插入止动位置拧紧螺钉图425：导线准备和插入盒式接线盒17.1.1.3 IC694TBS032和TBS132弹簧式接线盒，36个端子图426：，用于高密度PACSystems RX3i模块和等效的90-30系列PLC模块。这些接线板为模块的现场接线提供36个弹簧式端子。接线板IC694TBS032和TBS132功能相同。接线板IC694TBS032带有标准深度的外壳。安装时，其深度与大多数其他PACSystems和Series 90-30 PLC模块相同。扩展接线板IC694TBS132配有一个比接线板IC6914TBS032深约½英寸（13mm）的外盖，以容纳绝缘较厚的电线，例如通常用于交流输入/输出模块的电线。17.1.1.3.1规格：TBS032和TBS132线条长度7.87 mm（0.310 in）线规支持#14-28 AWG（实心或绞合）PACSystems*RX3i系统手册附录专用模块825 17.1.2安装和拆卸高密度接线板本节有高密度接线盒的特殊安装说明。有关一般安装信息，请参阅第2章。警告：安装或拆卸接线板组件时，必须关闭现场电源。17.1.2.1安装或拆除模块的接线板组件安装或拆除接线板模块组件1。将模块附带的小目录号标签（例如：“MDL240”）安装在接线板顶部的插槽中。2.完成模块接线并将线束固定到接线板底部的系紧装置上。PACSystems*RX3i系统手册附录专用模块826 17.1.2.2
17.1 High-Density Module-Mounted Terminal Blocks Terminal Block Type Catalog Number Box-style Terminal Block, 36 Terminals IC694TBB032 Spring-style Terminal Block, 36 Terminals IC694TBS032 Extended Box-style Terminal Block, 36 Terminals IC694TBB132 Extended Spring-style Terminal Block, 36 Terminals IC694TBS132 PACSystems* RX3i System Manual Appendix Special Purpose Modules 822 17.1.1 Terminal Blocks for High-Density RX3i Modules 17.1.1.1 Extended High-Density vs. High-Density Terminal Blocks Extended High-Density Terminal Blocks IC694TBB132 and IC694TBS132 are functionally identical to HighDensity Terminal Blocks IC694TBB032 and IC694TBS032. Both attach directly to the I/O module. The Extended High-Density Terminal Blocks have an outer cover that is approximately 13 mm (½ in) deeper. This is to accommodate wires with thicker insulation, such as wires typically used with AC I/O modules. 13mm (0.5 inch) Added Depth of Extended High-Density Terminal Block Figure 422: Additional Depth due to Extended High-Density Terminal Blocks Figure 423 compares the space for wiring on a High-Density Terminal Block (left) and an Extended HighDensity Terminal Block (right), seen from the bottom of the module. 10mm ( 0.4 inch) 23mm ( 0.9 inch) Figure 423: Depth Comparison: is the same depth as most other PACSystems and Series 90-30 PLC modules. Extended Terminal Block IC694TBB132 comes with an outer cover that is approximately 13 mm (½ in) deeper than Terminal Block IC694TBB032, to accommodate wires with thicker insulation, such as that typically used with AC I/O modules. 17.1.1.2.1 Specifications: TBB032 and TBB132 Torque 0.79 Nm (7 in-lb) Wire strip length 7.87 mm (0.310 in) Wire gauges supported #14-26 AWG (solid or stranded) 17.1.1.2.2 Connecting Field Wiring to a Box-Style High-Density Terminal Block The bottom of the terminal block can be used as a gauge for the wire strip length, as displayed in Figure 425. The stripped wire must be fully inserted into the terminal block so that the insulation meets the stop position inside the terminal, and the end of the wire is bent. Tightening the terminal screw raises the wire and clamps it in place. PACSystems* RX3i System Manual Appendix Special Purpose Modules 824 Wire strip length Insert wire to stop position Tighten screw Figure 425: Wire Preparation and Insertion into Box-Style Terminal Block 17.1.1.3 IC694TBS032 and TBS132 Spring-Style Terminal Blocks, 36 Terminals Figure 426: 36-Terminal Spring-Style Terminal Block Spring-Style Terminal Blocks, IC694TBS032 and IC694TBS132, are used with High-Density PACSystems RX3i modules and equivalent Series 90-30 PLC modules. These terminal blocks provide 36 spring style terminals for field wiring to the module. Terminal Blocks IC694TBS032 and TBS132 are functionally identical. Terminal Block IC694TBS032 comes with a standard-depth outer cover. When installed, it is the same depth as most other PACSystems and Series 90-30 PLC modules. Extended Terminal Block IC694TBS132 comes with an outer cover that is approximately ½ inch (13mm) deeper than Terminal Block IC694TBS032, to accommodate wires with thicker insulation, such as that typically used with AC I/O modules. 17.1.1.3.1 Specifications: TBS032 and TBS132 Wire strip length 7.87 mm (0.310 in) Wire gauges supported #14-28 AWG (solid or stranded) PACSystems* RX3i System Manual Appendix Special Purpose Modules 825 17.1.2 Installing and Removing High-Density Terminal Blocks This section has special installation instructions for High-Density Terminal Blocks. Refer to Chapter 2 for general installation information. WARNING Field power must be turned off when installing or removing a Terminal Block assembly. 17.1.2.1 Installing or Removing the Terminal Block Assembly of a Module To install or remove the terminal block module assembly 1. Install the small catalog number label (for example: “MDL240”) supplied with the module in the slot on the top of the Terminal Block. 2. Complete the module wiring and secure the wire bundles to the tie downs on the bottom of the Terminal Block. PACSystems* RX3i System Manual Appendix Special Purpose Modules 826 17.1.2.2
