HIEE300936R0001 UFC718AE01工控模块机器人备件
§内置命令行界面功能，通过模块的Micro USB端口或以太网Telnet支持直接监控和部分配置。§支持星形（交换）和线性（菊花链）网络拓扑。§四个交换以太网端口（位于下侧）-o两个8芯RJ-45屏蔽双绞线10/100/1000 Mbps铜接口；o两个小型可插拔（SFP）笼，用于用户提供的SFP设备。§与RX3i CPU同步的内部时钟，用于时间戳诊断。§模块支持插入和取出通电的RX3i通用背板。参见第2.6.4.1节热插拔▪ 模块支持使用WinLoader软件实用程序（如果主机CPU具有串行端口）或使用基于Web的工具（如果主机没有串行端口）进行固件升级。固件升级套件中包含说明。23注意：USB端口仅用于系统设置和诊断。它不能保持永久连接。16.11.1规范：ECM850协议支持IEC 61850客户端，符合PIC和MIC规范电源要求3.3Vdc:1.2 A，未安装SFP设备，最大1.9 A（安装2个SFP设备，每个SFP设备0.35 A）5Vdc:1.1 A最大工作温度范围0至60°C降级至57°C：•如果安装了100 MB光纤SFP，或•如果铜SFP以1 GB运行。端口连接器数量两个RJ-45和两个SFP笼（不包括SFP设备，单独提供）PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块748 Micro USB连接器一，用于使用命令行接口与计算机通信。局域网（LAN）IEEE 802.2逻辑链路控制I类IEEE 802.3 CSMA/CD介质访问控制10/100/1000 Mbps CPU状态位32轮询率90可为0到31267 ms的每个IED连接配置（默认为1000 ms）。IP地址数一个MAC地址数五个。每个外部端口一个，内部端口一个。网络拓扑支持星形（交换）、线性（菊花链）时间同步SNTP客户端–多播和广播系统每个RX3i CPU四（4）的最大限制ECM850。所有部件必须位于主机架中。（不支持在远程或扩展机架中使用）。每个ECM850支持的IED连接数量32每个ECM850 5000个IED（PPV）每个RX3i CPU 20000 16.11.1.1指示灯LED 90每个IED连接的轮询率可由IEC 61850配置器配置。ECM850还支持使用报告控制块（RCB）的非请求通信。基于RCB触发选项，无论轮询速率如何，RCB都可以用于更快的更新。更多详细信息，请参阅PACSystems RX3i IEC 61850以太网通信模块用户手册GFK-2849。91 PLC协议变量被定义为一组RX3i控制器变量，其在变量列表中以结构化格式表示IEC 61850协议数据属性。这通常包括对IED执行WRITE操作所需的附加变量。更多详细信息，请参阅PACSystems RX3i IEC 61850以太网通信模块用户手册GFK-2849。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块749下表总结了发光二极管（LED）指示灯功能。PACSystems RX3i IEC 61850以太网通信模块用户手册GFK-2849中提供了有关错误指示和闪烁模式的更多详细信息。OK表示模块是否能够执行正常操作。LAN表示对以太网局域网（LAN）的访问和活动。LAN LED指示网络接口正在处理网络数据包（不只是通过嵌入式交换机）STATUS指示正常操作期间ECM850的状态。它指示模块的本地日志中是否存在启动事件以外的条目。STATUS还可以指示
§ Built-in command-line interface function that supports direct monitoring and partial configuration by means of the module’s Micro USB port or Telnet over Ethernet. § Support for both star (switched) and linear (daisy-chained) network topologies. § Four switched Ethernet ports (located on the underside) — o Two 8-conductor RJ-45 shielded twisted pair 10/100/1000 Mbps copper interfaces; o Two Small Form-factor Pluggable (SFP) cages for user-supplied SFP devices. § Internal clock synchronized with the RX3i CPU for time-stamped diagnostics. § Module supports insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1 ▪ Module supports firmware upgrades using the WinLoader software utility (if the host CPU has a serial port) or using a Web-based tool (if the host CPU has no serial port). Instructions are included with the firmware upgrade kit.23 Note: The USB port is intended for system setup and diagnostics only. It must not remain permanently connected. 16.11.1 Specifications: ECM850 Protocol Support IEC 61850 Client as per PICs and MICs specifications Power Requirements 3.3Vdc: 1.2 A with no SFP devices installed 1.9 A maximum (2 SFP devices installed, 0.35 A per SFP device) 5Vdc: 1.1 A maximum Operating Temperature Range 0 to 60°C De-rated to 57°C: • if 100 MB Fiber SFPs installed, or • if Copper SFPs operating at 1 GB. Number of Port Connectors Two RJ-45 and Two SFP Cages (SFP devices not included, available separately.) PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 748 Micro USB Connector One, for communication with a computer using Command Line Interface. Local Area Network (LAN) IEEE 802.2 Logical Link Control Class I IEEE 802.3 CSMA/CD Medium Access Control 10/100/1000 Mbps CPU Status Bits 32 Polling Rate90 Configurable for every IED connection from 0 to 31267 ms (default is 1000 ms). Number of IP Addresses One Number of MAC Addresses Five. One per external port and one internal. Network Topologies Supported Star (switched), linear (daisy-chain) Time Synchronization SNTP Client – Multicast and Broadcast System Maximum Limits ECM850s per RX3i CPU Four (4). All must be located in main rack. (Use in remote or expansion racks not supported). No of IED connections supported per ECM850 32 No of IED (PPVs) per ECM850 5000 No of PPVs per RX3i CPU 20000 16.11.1.1 Indicator LEDs 90 The polling rate for each IED connection can be configured by the IEC 61850 Configurator. ECM850 also supports unsolicited communication using report control blocks (RCB). The RCB can be used for faster updates irrespective of polling rate, based on RCB trigger options. Refer to PACSystems RX3i IEC 61850 Ethernet Communication Module User Manual, GFK-2849 for more details. 91 PLC Protocol Variables is defined as the set of RX3i controller variables which represents the IEC 61850 protocol data attributes in a structured format in a variable list. This typically includes the additional variables which are required to perform WRITE operations to an IED. Refer to PACSystems RX3i IEC 61850 Ethernet Communication Module User Manual, GFK-2849 for more details. PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 749 The following table summarizes the light-emitting diode (LED) indicator functions. More detailed information about error indications and blink patterns is given in PACSystems RX3i IEC 61850 Ethernet Communication Module User Manual, GFK-2849. OK Indicates whether the module is able to perform normal operation. LAN Indicates access to and activity on the Ethernet local area network (LAN). The LAN LED indicates network packets are being processed by the network interface (not just passing through the embedded switch) STATUS Indicates the condition of the ECM850 during normal operation. It indicates whether an entry other than the startup event is present in the module’s local log. STATUS can also indicate whether any of
