HIEE400106R1 CSA464AE模块卡件
示例：如果单词9和11分别包含值8和250，则响应将写入%R251。字12基于0的偏移量（高位字）偏移量的高位字。对于大多数内存类型，值为0。仅当使用%W内存时，高位字才为非零。69 COMMREQ状态字由两个内存字组成。低位16位字提供COMMREQ状态，高位16位字则提供命令状态。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月带HART通信的模拟模块543字偏移值Dec（十六进制）定义字13字：90（005A）字节：180（00B4）最大响应区域大小。如果使用单词记忆类型，则必须为90；如果使用离散存储器类型，则为180。单词14范围1-16。信道编号1-16（有效范围取决于模块信道计数和单端与差分模式）字15远程PROFINET扫描仪的设备ID ID。支持HART的模拟模块的字16插槽远程机架插槽编号。字17支持HART的模拟模块的子插槽远程机架子插槽编号11.6.2.1命令状态字远程获取HART设备信息命令的命令状态字显示在下图中。值描述Dec（十六进制）0（0000）无命令特定状态可用。1（0001）PROFINET设备号无效。2（0002）未声明的PROFINET设备（名称无效或不存在）。3（0003）插槽或子插槽编号无效。4（0004）非特定PROFINET错误。5（0005）信道号无效。6（0006）非特定命令错误。11.6.2.2最低固件和GSDML要求远程获取HART设备信息COMMREQ需要以下固件版本和GSDMLs：·版本为8.95或更高版本的RX3i CPU·版本为2.26或更高的IC695PNC001 RX3i PROFINET控制器·版本为2.41或更高，或IC695PNS101·IC695PNS001 RX3i PROFINET扫描仪GSDML-V2.3-GEIP-RX3iPNS-20160602.xml注意，需要更新的IC695PNSO01 RX3iPROFINET扫描仪GSML-V2.3-GEIP-RX3iPNS-20160602.xml才能启用PME中支持HART的模拟模块的HART直通服务选项设置。设置为：PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月带有HART通信的模拟模块544·每信道扫描一次·每两信道扫描一（默认）·每四信道扫描一·仅通过前三个选项设置设置支持HART通信的模拟模块向HART设备查询其远程获取HART设备的速率信息数据。然而，仅通过设置配置信道扫描，仅在HART设备配置更改或10秒未读取时发生。注意，当“仅通过”设置为选择信息、回复数据格式、远程和本地Gees 20-23的响应时，远程获取HART设备信息功能不起作用。类型：REAL 21-24插槽0值CMD#33，字节2-5。类型：BYTE 25-28插槽1值CMD#33，字节8-11。类型：BYTE 29-32插槽2值CMD#33，字节14-17。类型：BYTE 33-36插槽3值CMD#33，字节20-23。类型：上一次HART命令响应的BYTE 37 HART通信状态字节，请参阅下一页PACSystems*RX3i系统手册第12节GFK-2314T变量代码CMD#50，字节2类型：BYTE 84
.Example: If Words 9 and 11 contain values of 8 and 250 respectively, the response will be written to %R251. Word 12 0-based offset (high word) High word of offset. Value = 0 for most memory types. High word is non-zero only on if %W memory is used. 69 The COMMREQ status words consist of two words of memory. The lower 16-bit word provides the COMMREQ Status and the upper 16-bit word provides the Command Status. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART Communications 543 Word Offset Value Dec (Hex) Definition Word 13 Words: 90 (005A) Bytes: 180 (00B4) Maximum size of response area. Must be 90 if word memory type is used; 180 if discrete memory type is used. Word 14 Range 1-16. Channel Number 1-16 (valid range depends on module channel count and single-ended versus differential mode) Word 15 Device ID ID of Remote PROFINET Scanner. Word 16 Slot Remote Rack Slot number of HART capable Analog module. Word 17 SubSlot Remote Rack SubSlot number of HART capable Analog module 11.6.2.1 Command Status Word The Command status word for the Remote Get HART Device Information command is displayed in the following figure. Value Description Dec (Hex) 0 (0000) No command-specific status available. 1 (0001) Invalid PROFINET device number. 2 (0002) Undeclared PROFINET device (invalid name or nonexistent). 3 (0003) Invalid slot or subslot number. 4 (0004) Non-specific PROFINET error. 5 (0005) Invalid channel number. 6 (0006) Non-specific command error. 11.6.2.2 Minimum Firmware & GSDML Requirements The Remote Get HART Device Information COMMREQ requires the following firmware revisions and GSDMLs: · RX3i CPUs with version 8.95 or later · IC695PNC001 RX3i PROFINET Controller version 2.26 or later · IC695PNS001 RX3i PROFINET Scanner version 2.41 or later, or IC695PNS101 · IC695PNS001 RX3i PROFINET Scanner GSDML-V2.3-GEIP-RX3iPNS-20160602.xml Note that the updated IC695PNS001 RX3i PROFINET Scanner GSDML-V2.3-GEIP-RX3iPNS-20160602.xml is required to enable the HART Pass Through Service Options settings for HART capable analog modules in PME. The settings are: PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART Communications 544 · Once per Channel Scan · Once per Two Channel Scans (default) · Once per Four Channel Scans · Pass-Thru Only The first three option settings set the rate at which an analog module that supports HART communications queries a HART device for its Remote Get HART Device Information data. Whereas, the Pass-Thru Only setting configures channel scanning that occurs only when the HART device configuration changes or has not been read for 10 seconds. Note that the Remote Get HART Device Information feature does not work when the “Pass-Thru Only” setting is sele ice Information, Reply Data Format The response to a Remote and Local Ge es 20-23. Type: REAL 21-24 Slot 0 value CMD#33, Bytes 2-5. Type: BYTE 25-28 Slot 1 value CMD#33, Bytes 8-11. Type: BYTE 29-32 Slot 2 value CMD#33, Bytes 14-17. Type: BYTE 33-36 Slot 3 value CMD#33, Bytes 20-23. Type: BYTE 37 HART communication status byte from the last HART command response, refer to next page PACSystems* RX3i System Manual Section 12 GFK-2314T Variable Code CMD#50, Byte 2 Type: BYTE 84
