HIEE-410110-P2工业卡件,ABB卡件
接线板单独订购。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月带HART IC695ALG628的模拟模块无热降额。模块IC695ALG626在电压模式下没有热降额。电流模式下IC695ALG626的热降额如图313所示。分辨率请参阅下面的分辨率和范围类型表。输入数据格式可配置为32位字段中的浮点IEEE 32位或16位整数。滤波器选项8Hz、12Hz、16Hz、40Hz、200Hz、500Hz模拟模块扫描时间（ms）模块扫描最多可包含四个采集周期。每个周期包括一组特定的通道，如下面的通道扫描部分所述。总扫描时间取决于扫描中的采集周期数、配置的滤波器选项以及信道是模拟还是HART。HART通信498 HART数据扫描时间（以秒为单位）HART数据扫描可包括多达四个采集周期（类似，但扫描周期、重试次数、插槽变量的启用/禁用以及直通命令的使用）。如果插槽变量被启用，更新时间将加倍。HART组中的信道启用次数：每个HART数据信道每：1 0.7秒更新一次（典型）2 1.9秒（典型值）3 3.0秒（典型）4 4.0秒（通常值）输入阻抗>100kW电压输入电流输入电阻249W±1%开路检测时间1秒最大过电压±60 Vdc连续，最大过电流±28mA连续，50Hz时最大正常模式噪声抑制（dB）60Hz时8 Hz滤波器85 85 12 Hz滤波器85 86 16 Hz滤波器35 62 40 Hz滤波器3 6 200 Hz滤波器0 0 500 Hz 0 0共模噪声抑制在50/60 Hz时最小120dB，8 Hz滤波器在50/60赫兹时最小110dB，12 Hz滤波器信道直流串扰-最小80 dB（单端模式）-最小80分贝（差分模式，接地公共）-60 dB最小（差分模块状态）。现场状态LED指示至少一个通道上存在故障或接线板错误。TB（接线板）LED指示接线板的存在或不存在。LED由背板电源总线供电。LED状态指示模块正常开启绿色模块正常并配置为绿色或琥珀色，缓慢闪烁错误绿色，快速闪烁模块正常但未配置PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月带HART通信500关闭模块的模拟模块有故障或无背板电源现场状态开启绿色任何已启用通道无故障，且至少一个通道上存在接线板ON黄色故障断开接线板不存在或未完全就位TB ON红色接线板不出现或未完全到位ON绿色接线板存在OFF模块无背板电源11.2.3配置：ALG626和ALG628 11.2.3.1模块参数默认描述通道值参考地址%AIxxxxx启动此模块的输入数据的地址。这默认为下一个可用的%AI块。该数据的格式如第0节所示。信道值参考长度ALG628:16用于此模块输入数据的字数。此ALG626:32参数无法更改。诊断参考地址%Ixxxxx通道诊断状态数据的起始地址。该数据的格式如第11.2.4.2节所示。诊断参考长度0信道诊断数据所需的位参考位数。设置为0时，通道诊断被禁用。要启用通道诊断映射，请将其更改为非零值。Terminal Blocks are ordered separately. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART IC695ALG628 has no thermal derating. Module IC695ALG626 has no thermal derating in voltage mode. Thermal derating for IC695ALG626 in current mode is shown in Figure 313. Resolution Refer to Resolution and Range Type table below. Input Data Format Configurable as floating-point IEEE 32-bit or 16-bit integer in a 32-bit field. Filter Options 8Hz, 12Hz, 16Hz, 40Hz, 200Hz, 500Hz Analog Module Scan Time (ms) The module scan can consist of up to four acquisition cycles. Each cycle includes a specific set of channels, as described in the Channel Scanning section below. Total Scan Time depends on the number of acquisition cycles in the scan, the configured filter option, and whether the channels are analog or HART. HART Communications 498 HART Data Scan Time (in seconds) The HART data scan can consist of up to four acquisition cycles (similar but cycles in the scan, number of retries, enabling/disabling of slot variables, and use of Pass-Through commands. If slot variables are enabled, update times are doubled. # Channels in Group Enabled for HART: Each HART Data Channel updates every: 1 0.7 second (typical) 2 1.9 seconds (typical) 3 3.0 seconds (typical) 4 4.0 seconds (typical) Input Impedance >100kW voltage inputs Current Input Resistance 249W ±1% Open Circuit Detection time 1 second maximum Over-voltage ±60 Vdc continuous, maximum Overcurrent ±28mA continuous, maximum Normal Mode Noise Rejection in dB At 50Hz At 60Hz 8 Hz filter 85 85 12 Hz filter 85 85 16 Hz filter 35 62 40 Hz filter 3 6 200 Hz filter 0 0 500 Hz 0 0 Common Mode Noise Rejection 120dB minimum at 50/60 Hz with 8 Hz filter 110dB minimum at 50/60 Hz with 12 Hz filter Channel-Channel DC Crosstalk -80 dB minimum (single ended mode) -80 dB minimum (differential mode, grounded common) -60 dB minimum (differential module status. The Field Status LED indicates the presence of a fault on at least one channel or a terminal block error. The TB (Terminal Block) LED indicates the presence or absence of the terminal block. LEDs are powered from the backplane power bus. LED State Indicates Module OK ON Green Module OK and configured Green or Amber, blinking slowly Error Green, blinking rapidly Module OK but not configured PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART Communications 500 OFF Module is defective or no backplane power present Field Status ON Green No faults on any enabled channel, and Terminal Block is present ON Yellow Fault on at least one channel OFF Terminal block not present or not fully seated TB ON Red Terminal block not present or not fully seated ON Green Terminal block is present OFF No backplane power to module 11.2.3 Configuration: ALG626 and ALG628 11.2.3.1 Module Parameters Parameter Default Description Channel Value Reference Address %AIxxxxx Starting address for the input data of this module. This defaults to the next available %AI block. The format of this data is shown in Section 0. Channel Value Reference Length ALG628: 16 The number of words used for the input data of this module. This ALG626: 32 parameter cannot be changed. Diagnostic Reference Address %Ixxxxx Starting address for the channel diagnostics status data. The format of this data is shown in Section 11.2.4.2. Diagnostic Reference Length 0 The number of bit reference bits required for the Channel Diagnostics data. When set to 0, Channel Diagnostics is disabled. To enable Channel Diagnostics mapping, change this to a nonzero value.
