HIEE451116RW01输出卡件
该模块的命令反馈数据。配置非零长度后，默认为下一个可用%AI地址。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块473输出命令反馈长度0用于此模块命令反馈数据的字数。长度默认为0。它可以设置为16。诊断参考地址%Ixxxxx通道诊断状态数据的起始地址。这默认为下一个可用的%I块。诊断参考长度0只读。通道诊断数据所需的位参考位数。默认值为0，这意味着禁用通道诊断映射。将其更改为非零值以启用通道诊断映射。模块IC695ALG808的最大长度为256位。模块状态参考地址%Ixxxxx此模块状态数据的起始地址。这默认为下一个可用的%I块。模块状态参考长度0只读。模块状态数据所需的位数（0或32）。默认值为0，这意味着模块状态数据的映射被禁用。将其更改为非零值以启用模块状态数据映射。10.4.5.1.1模拟输出命令反馈模块将从CPU接收的模拟输出数据的副本返回到其相应的通道模拟输入共享存储器中。可以监控输出反馈，以检查发送到通道的值。数据采用与每个通道的输出数据相同的缩放格式。在正常操作期间，该反馈数据应与模块输入的一次或多次PLC扫描后的实际输出数据相匹配。在故障、斜坡、超范围和箝位条件下，模拟输出数据可能与命令输出不同。10.4.5.1.2过高温度如果启用了过高温度，如果该模块的内部温度对于同时打开的输出数量而言过高，则模块会生成过高温度警报。除了超温故障报告和中断的可配置选项外，超温状态也由该模块状态参考数据中的超温位指示。始终启用过热状态位的检测。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块474模块参数（续）参数默认说明I/O扫描集1将模块I/O状态数据分配给CPU配置中定义的扫描集。确定RX3i在未启用/禁用端子块的情况下轮询数据通道故障的频率：控制端子块移除后是否会生成通道故障和配置的报警响应。默认设置为Disabled（禁用）意味着移除接线板时，通道故障和报警被抑制。此参数不影响模块故障，包括启用的接线板丢失/添加故障损坏报告，此参数控制现场断电模块故障的中断。过热启用禁用启用
command feedback data of this module. This defaults to the next available %AI address after a non-zero length is configured. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 473 Output Command Feedback Length 0 The number of words used for the command feedback data of this module. Length defaults to 0. It can be set to 16. Diagnostic Reference Address %Ixxxxx Starting address for the channel diagnostics status data. This defaults to the next available %I block. Diagnostic Reference Length 0 Read Only. The number of bit reference bits required for the Channel Diagnostics data. Default is 0, which means mapping of Channel Diagnostics is disabled. Change this to a non-zero value to enable Channel Diagnostics mapping. Maximum length is 256 bits for module IC695ALG808. Module Status Reference Address %Ixxxxx Starting address for the status data of this module. This defaults to the next available %I block. Module Status Reference Length 0 Read Only. The number of bits (0 or 32) required for the Module Status data. Default is 0, which means mapping of Module Status data is disabled. Change this to a non-zero value to enable Module Status data mapping. 10.4.5.1.1 Analog Output Commanded Feedback The module returns a copy of the analog output data received from the CPU in its corresponding channel analog input shared memory. Output Feedback can be monitored to check the values being sent to the channels. The data is in the same scaled format as the output data for each channel. During normal operation, this feedback data should match the actual output data after one or more PLC scans of module inputs. During faults, ramping, over-range, and clamping conditions, the analog output data may differ from the commanded output. 10.4.5.1.2 Over-Temperature If Over-Temperature is enabled, the module generates an Over-Temperature alarm if the internal temperature of this module is too great for the number of outputs that are on at the same time. In addition to the configurable options for Over-Temperature fault reporting and interrupts, an over temperature condition is also indicated by the Over-Temperature bit in the Status Reference data of this module. Detection of the Over-Temperature status bit is always enabled. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 474 Module Parameters (Continued) Parameter Default Description I/O Scan Set 1 Assigns the module I/O status data to a scan set defined in the CPU configuration. Determines how often the RX3i polls the data Channel Faults w/o Terminal Block Disabled Enabled / Disabled: Controls whether channel faults and configured alarm responses will be generated after a Terminal Block removal. The default setting of Disabled means channel faults and alarms are suppressed when the Terminal Block is removed. This parameter does not affect module faults including the Terminal Block loss/add fault rrupt Reporting enabled, this parameter controls interrupts for Field Power Removed module faults. Over Temp Enabled Disabled Enabled
