HIEE451116RW01 FW9925a-E工控模块机器人备件
请参阅上文。ON绿色：存在接线板。请参阅上文。OFF：模块没有背板电源。10.4.4规格：IC695ALG808输出范围电流：0至20mA，4至20mA电压：±10 Vdc，0至10 Vdc ALG808-FA及更早版本背板电源要求：3.3V时最大450mA；对于ALG808-GB和更高版本，5.0V时最大25mA：3.3V时最大250mA；模块内5.0V功耗时最大17mA最大7.25瓦（Vuser=24V）热降级无需外部+电源电压范围：19.2V至30V（24V标称）电流：660mA最大PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块472分辨率±10 Vdc：15位，0至10 Vdc：14位，0到20mA:15位，4至20mA：15位输出数据格式，可配置为浮点IEEE 32位或32位字段中的16位整数模拟更新速率（由I/O扫描时间确定，取决于应用程序）8 ms（近似值，所有8个通道）输出过压保护电流输出仅：-30 V，持续60秒，+30V一小时校准精度64在25°C（从0到0.05mA，精度为±35µA）下精确到满量程的0.10%以内在0-60°C（0到0.05毫安，精度为？0µA）时精确到满刻度的0.25%以内输出负载电抗电流：最大10µH，电压：1µF最大最大输出负载电流：1350W最大电压：2kW最小输出增益漂移电压输出：每摄氏度20ppm典型电流输出：每华氏度35ppm典型输出设定时间电压或电流输出：2ms，0至95%隔离，场至背板2550 Vdc，1秒隔离，每个通道10.4.5配置：IC695ALG008 10.4.5.1模块参数默认描述输出参考地址%AQxxxxx此模块输出数据的起始地址。这默认为下一个可用的%AQ块。输出参考长度16用于此模块输出数据的字数。无法更改此参数。输出命令反馈参考地址%AIxxxxx
Refer to above. ON Green: Terminal block is present. Refer to above. OFF: No backplane power to module. 10.4.4 Specifications: IC695ALG808 Output Ranges Current: 0 to 20mA, 4 to 20mA Voltage: ±10 Vdc, 0 to 10 Vdc Backplane Power Requirements For ALG808-FA and earlier: 450mA maximum at 3.3V; 25mA maximum at 5.0V For ALG808-GB and later: 250mA maximum at 3.3V; 17mA maximum at 5.0V Power Dissipation within Module 7.25 Watts maximum (Vuser=24V) Thermal De-rating None required External +Power Supply Voltage Range: 19.2V to 30V (24V nominal) Current: 660mA maximum PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 472 Resolution ±10 Vdc: 15 bits, 0 to 10 Vdc: 14 bits, 0 to 20mA: 15 bits, 4 to 20mA: 15 bits Output Data Format Configurable as floating-point IEEE 32-bit or 16-bit integer in a 32-bit field Analog Update Rate (Determined by I/O scan time, application dependent) 8 ms (approximate, all eight channels) Output Over-voltage Protection Current outputs only: -30V for 60 seconds, +30V for one hour Calibrated Accuracy64 Accurate to within 0.10% of full scale at 25°C (From 0 to 0.05mA, accuracy is ±35µA) Accurate to within 0.25% of full scale at 0-60°C (From 0 to 0.05mA, accuracy is ±70µA) Output Load Reactance Current: 10µH maximum, Voltage: 1µF maximum Maximum Output Load Current: 1350W maximum Voltage: 2kW minimum Output Gain Drift Voltage output: 20ppm per degree C typical Current output: 35ppm per degree C typical Output Settling Time Voltage or current output: 2ms, 0 to 95% Isolation, Field to Backplane 2550 Vdc for one second Isolation, Channel to Channel 250 Vac continuous 1500 Vac for one minute per channel 10.4.5 Configuration: IC695ALG808 10.4.5.1 Module Parameters Parameter Default Description Outputs Reference Address %AQxxxxx Starting address for the output data of this module. This defaults to the next available %AQ block. Outputs Reference Length 16 The number of words used for the output data of this module. This parameter cannot be changed. Output Command Feedback Reference Address %AIxxxxx Stating address for the
