HIMA F1201模块卡件
I除了超温故障报告和中断的可配置选项外，超温状态也由该模块状态参考数据中的超温位指示。始终启用过热状态位的检测。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块454模块参数（续）参数默认说明I/O扫描集1将模块I/O状态数据分配给CPU配置中定义的扫描集。确定RX3i在未启用/禁用端子块的情况下轮询数据通道故障的频率：控制端子块移除后是否会生成通道故障和配置的报警响应。默认设置为Disabled（禁用）意味着移除接线板时，通道故障和报警被抑制。此参数不影响模块故障，包括接线板丢失/添加故障生成。模块故障报告启用启用启用/禁用。控制模块是否会报告因失去现场电源或温度过高而导致的故障。现场电源移除启用启用启用/禁用。启用模块故障报告后，此参数控制现场断电模块故障的报告。过热启用启用启用/禁用。启用模块故障报告后，此参数控制超温模块故障的报告。模块中断报告启用禁用启用/禁用。现场断电已启用已禁用已启用/已禁用。启用模块中断报告后，此参数控制现场断电模块故障的中断。过热启用禁用启用/禁用。启用模块中断报告后，此参数控制过热模块故障的中断。范围类型禁用电流设置要用于每个通道的输出类型。选项包括：禁用电压、禁用电流、电流/电压。范围（仅用于清除配置。选项为保持最后状态，或默认为特定配置的默认值。10.3.13.1.3范围类型应为电流/电压配置模块上的每个通道。然后可根据需要配置其电压或电流范围和其他参数。如果不使用通道输出且未连接，则选择“禁用”选项如果通道被禁用，则不必启用▪ 背板电源不正常。在这种情况下，即使已启用斜坡，也没有斜坡。▪ 失去与CPU的通信。▪ I/O通信丢失。▪ 磁场功率损失。输出默认注释▪ 在I/O启用模式下热移除模块将导致所有输出保持最后状态（甚至配置为强制默认值的通道）。如果不需要该操作，则可通过首先关闭现场电源并在热卸下模块之前卸下该模块的接线板，将输出强制设置为默认值。▪ 即使配置了默认值，使用SVC_REQ 24重置模块也会导致所有通道保持最后状态。应用程序必须在执行Service Request之前处理输出默认值。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块n addition to the configurable options for Over-Temperature fault reporting and interrupts, an over temperature condition is also indicated by the Over-Temperature bit in the Status Reference data of this module. Detection of the Over-Temperature status bit is always enabled. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 454 Module Parameters (Continued) Parameter Default Description I/O Scan Set 1 Assigns the module I/O status data to a scan set defined in the CPU configuration. Determines how often the RX3i polls the data Channel Faults w/o Terminal Block Disabled Enabled / Disabled: Controls whether channel faults and configured alarm responses will be generated after a Terminal Block removal. The default setting of Disabled means channel faults and alarms are suppressed when the Terminal Block is removed. This parameter does not affect module faults including the Terminal Block loss/add fault generation. Module Fault Reporting Enabled Enabled Enabled / Disabled. Controls whether the module will report faults resulting from either loss of field power or overtemperature conditions. Field Power Removed Enabled Enabled Enabled / Disabled. With Module Fault Reporting enabled, this parameter controls reporting of Field Power Removed module faults. Over Temp Enabled Enabled Enabled / Disabled. With Module Fault Reporting enabled, this parameter controls reporting of Over-temperature module faults. Module Interrupt Reporting Enabled Disabled Enabled / Disabled. Field Power Removed Enabled Disabled Enabled / Disabled. With Module Interrupt Reporting enabled, this parameter controls interrupts for Field Power Removed module faults. Over Temp Enabled Disabled Enabled / Disabled. With Module Interrupt Reporting enabled, this parameter controls interrupts for Over-temperature module faults. Range Type Disabled Current Sets up the type of output to be used for each channel. Choices are: Disabled Voltage, Disabled Current, Current/Voltage. Range (Only for configuration is cleared. Choices are Hold Last State, or default to a specific configured default value. 10.3.13.1.3 Range Type Each channel on the module that will be used should be configured for Current/Voltage. Its voltage or current range and other parameters can then be configured as needed. If the channel output will not be used and is not wired, select either “Disabled” option. If a channel is disabled, it is not necessary not enabled ▪ Backplane power is not ok. In that case, there is no ramping, even if ramping has been enabled. ▪ Loss of communications from CPU. ▪ Loss of I/O communications. ▪ Loss of field power. Outputs Default Notes ▪ Hot Removal of the module in an I/O Enabled mode will cause all outputs to Hold Last State (even channels configured for Force to Default Value). If that operation is not desirable, the outputs can be forced to default by first turning off field power and removing the Terminal Block of this module before hot-removing the module. ▪ Resetting the module using SVC_REQ 24 causes all channels to Hold Last State even if Default Value is configured. The application program must handle output defaulting before execution of the Service Request. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules
