HIMA F2102处理器卡件
是符号位。范围分辨率范围限制0至20 mA 15位0至32767 4至20 mA 16位0至3296763 0至10 Vdc 15位0到32767-10 Vdc至10 Vdc 16位-32768至32767 10.3.5.1状态数据：ALG392此模块使用8或16个离散输入位，如配置所示。低8位用于模块状态信息，如下图所示。在当前模式下，各个通道也可以报告断线诊断。这些诊断以高8位报告，如图所示：63 in 4-20可配置为作为电压输出或电流输出运行，而不是同时运行。10.3.7配置：ALG392参数描述值默认值激活信道扫描的信道数1到8 1模块输出数据参考地址输出范围0、+10 Vdc±10 Vdc 4、20 mA 0、20 mA 1、10 Vdc激活信道表示PLC CPU将扫描的信道数量。对STOP模式所做的选择决定了当从RUN（运行）模式转到STOP（停止）模式时，该模块上的输出是否保持其最后状态或默认为零。%AQ参考地址参数选择%AQ内存中将开始向模块输出数据的区域的起始位置。%I参考地址选择%I内存中该模块状态数据区域的起始位置。如果长度设置为8，则只报告模块状态。如果长度设置为16，则还将报告作为电流输出运行的信道的信道状态。每个通道可设置为在四个输出范围之一上运行：▪ 0至10 Vdc（默认值）▪ -10 Vdc至+10 Vdc范围▪ 4至20 mA和0至20 mA▪ 0至20 mA 10.3.8模拟输出模块4通道电流/电压：IC695ALG004模拟输出模块8通道电流/电流：IC695AlG008 PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块449模块OK FIELD STATUS TB IC695ALG708 Q1 Q2 Q4 Q5 Q6 Q7 Q8图304:IC695ALL708模拟电流/电压输出模块IC695ALD704，提供四个非隔离的可配置电压或电流输出通道。模拟电流/电压输出模块IC695ALG008（图304）提供八个非隔离的可配置电压或电流输出通道。可以为以下输出范围配置模拟通道：▪ 电流：0至20mA，4至20mA▪ 电压：±10 Vdc，0至10 Vdc这些模块可与盒型（IC694TBB032）、扩展盒型（IC 694TBB132）、弹簧型（IC6914TBS032）或扩展弹簧型（IC 6914TBS132）接线板一起使用。扩展接线板提供屏蔽布线所需的额外护罩深度。有关接线板的更多信息，请参阅第17章。接线板单独订购。这些模块必须位于RX3i通用背板中。它们需要固件版本为3.0或更高版本的RX3i CPU。必须使用Machine Edition 5.0 SP3 Logic Developer PLC或更高版本进行配置。10.3.9隔离+24V直流电源模块必须从外部电源接收其24Vdc电源。外部电源必须直接连接到此模块的接线板。它不能通过RX3i通用背板上的TB1连接器连接。10.3.10特点：ALG704和ALG708▪ 完全软件可配置，无需设置模块跳线▪ 单独启用或禁用通道▪ 夹紧和报警限值▪ 警报的锁定▪ 可配置输出偏置▪ 基于滤波器频率的快速信道捕获时间▪ 全自动校准▪ 车载错误检查▪ 每个通道可配置的缩放和偏移▪ 每个通道可选择高报警、低报警、高高报警、低低报警检测和报告▪ 模块故障报告▪ 可配置的保持上次状态或输出默认值▪ 模块支持插入和取出通电的RX3i通用背板。参见第2.6.4.1节热插拔。▪ 模块支持使用WinLoader软件实用程序（如果主机CPU具有串行端口）或使用基于Web的工具（如果主机没有串行端口）进行固件升级。固件升级套件中包含说明。2
.is the sign bit. Range Resolution Range Limits 0 to 20 mA 15 bits 0 to 32767 4 to 20 mA 15 bits 0 to 3276763 0 to 10 Vdc 15 bits 0 to 32767 -10 Vdc to 10 Vdc 16 bits - 32768 to 32767 10.3.5.1 Status Data: ALG392 This module uses either 8 or 16 discrete input bits, as configured. The lower 8 bits are used for module status information as displayed in the following figure. In current mode, individual channels can also report Broken Wire diagnostics. Those diagnostics are reported in the upper eight bits, as shown: 63 In 4-20 can be configured to operate as a voltage output or a current output - not both simultaneously. 10.3.7 Configuration: ALG392 Parameter Description Values Default Values Active Channels Number of channels scanned 1 through 8 1 Reference Address for Module Output Data Starting Type of Output Range 0, +10 Vdc ±10 Vdc 4, 20 mA 0, 20 mA 0, 10 Vdc Active Channels indicates the number of channels that will be scanned by the PLC CPU. The choice made for STOP Mode determines whether the outputs on this module will hold their last states or default to zero when the goes from RUN to STOP mode. The %AQ Reference Address parameter selects the start of the area in the %AQ memory where the output data to the module will begin. The %I Reference Address selects the start of the area in %I memory for the status data of this module. If the length is set to 8, then only module status will be reported. If the length is set to 16, channel status will also be reported for channels that are operating as current outputs. Each channel can be set up to operate on one of four output ranges: ▪ 0 to 10 Vdc (default) ▪ -10 Vdc to +10 Vdc range ▪ 4 to 20 mA, and 0 to 20 mA ▪ 0 to 20 mA 10.3.8 Analog Output Module 4-Channel Current/Voltage: IC695ALG704 Analog Output Module 8-Channel Current/Voltage: IC695ALG708 PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 449 MODULE OK FIELD STATUS TB IC695ALG708 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Figure 304: IC695ALG708 The Analog Current/Voltage Output module, IC695ALG704, provides four non-isolated configurable voltage or current output channels. The Analog Current/Voltage Output module, IC695ALG708 (Figure 304), provides eight non-isolated configurable voltage or current output channels. Analog channels can be configured for these output ranges: ▪ Current: 0 to 20mA, 4 to 20mA ▪ Voltage: ± 10 Vdc, 0 to 10 Vdc These modules can be used with a Box-style (IC694TBB032), Extended Boxstyle (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) Terminal Block. Extended terminal blocks provide the extra shroud depth needed for shielded wiring. Refer to Chapter 17 for more information about Terminal Blocks. Terminal Blocks are ordered separately. These modules must be located in an RX3i Universal Backplane. They require an RX3i CPU with firmware version 3.0 or later. Machine Edition Version 5.0 SP3 Logic Developer-PLC or later must be used for configuration. 10.3.9 Isolated +24Vdc Power The module must receive its 24Vdc power from an external source. The external source must be connected directly to the terminal block of this module. It cannot be connected via the TB1 connector on the RX3i Universal Backplane. 10.3.10 Features: ALG704 & ALG708 ▪ Completely software-configurable, no module jumpers to set ▪ Individually enable or disable channels ▪ Clamping and Alarm Limits ▪ Latching of Alarms ▪ Configurable output bias ▪ Rapid channel acquisition times based on filter frequency ▪ Full auto-calibration ▪ On-board error-checking ▪ Configurable scaling and offsets per channel ▪ High alarm, low alarm, high-high alarm, low-low alarm detection and reporting selectable per channel ▪ Module fault reporting ▪ Configurable Hold Last State or Output Defaults ▪ Module supports insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. ▪ Module supports firmware upgrades using the WinLoader software utility (if the host CPU has a serial port) or using a Web-based tool (if the host CPU has no serial port). Instructions are included with the firmware upgrade kit.2
