HIMA F2108控制卡件
插入并从通电的RX3i通用背板中取出。参见第2.6.4.1节热插拔。模块支持使用WinLoader软件实用程序（如果主机CPU具有串行端口）或使用基于Web的工具（如果主机没有串行端口）进行固件升级。固件升级套件中包含说明。23 10.3.1隔离+24V直流电源模块必须从外部电源接收其24Vdc电源。如果模块位于RX3i通用背板中，则外部电源可通过背板左侧的TB1连接器连接，或直接连接到模块接线板。如果此模块位于扩展或远程背板中，则外部电源必须连接到此模块的接线板。10.3.2 LED：ALG392 PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块441模块OK LED指示模块状态。用户电源LED指示外部+24V直流电源是否存在且高于最低水平。两个LED均由+5Vdc背板电源总线供电。LED指示模块正常开启：模块正常且已配置闪烁：模块正常但未配置关闭：模块故障或不存在+5V背板电源用户电源开启：外部电源关闭：不存在用户电源10.3.3规格：ALG392输出通道数量1至8可选，单端输出电流范围4至20 mA和0至20 mA输出电压范围0至10 V和–10 V至+10 V校准工厂校准为0.625μA，适用于0至20毫安；0.5μA，4至20 mA；对于电压（每计数）用户电源电压（标称）+24V dc，3125 mV，来自用户电源外部电源电压范围20 Vdc至30 Vdc范围（最大值）62在存在严重RF干扰（IEC 801–3，10V/m）的情况下，电流输出的精度可能降低至±1%满量程（FS），电压输出的精度降低至±3%FS。PACSystems*RX3i系统手册第12节GFK-2314T 2019年9月模拟输出模块442最大符合电压VUSER–3 V（最小）至VUSER（最大）用户负载（电流模式）0至850Ω （VUSER=20 V时最小值，最大值1350Ω VUSER=30 V时）（负载小于800Ω 取决于温度。）输出负载电容（电流模式）2000 pF（最大值）输出负载电感（电流模式下）1 H输出负载（电压模式下）输出负载电容5 mA（最小电阻2kW）（最大电容1μF）隔离，场至背板（光学）和机架接地250 Vac连续；1500 Vdc，1分钟功耗110 mA，来自+5Vdc PLC背板电源，来自+24V直流用户电源，315 mA。有关产品标准和一般规范，请参阅附录A。为了满足附录A中规定的IEC 1000-4-3射频敏感度等级，当存在此模块时，系统必须安装在金属外壳中。PACSystems*RX3i系统手册第12节GFK-2314T 9月。
into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. Module supports firmware upgrades using the WinLoader software utility (if the host CPU has a serial port) or using a Web-based tool (if the host CPU has no serial port). Instructions are included with the firmware upgrade kit.23 10.3.1 Isolated +24Vdc Power The module must receive its 24Vdc power from an external source. If the module is located in an RX3i Universal Backplane, the external source can be connected via the TB1 connector on the left side of the backplane or directly to the module terminal block. If this module is located in an Expansion or Remote backplane, the external source must be connected to the terminal block of this module. 10.3.2 LEDs: ALG392 PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 441 The Module OK LED indicates module status. The User Supply LED indicates whether the external +24Vdc power supply is present and is above the minimum level. Both LEDs are powered from the +5Vdc backplane power bus. LED Indicates Module OK ON: Module OK and configured Flashing: Module OK but not configured OFF: Module is defective or no +5V backplane power present User Supply ON: External power supply present OFF: No user power 10.3.3 Specifications: ALG392 Number of Output Channels 1 to 8 selectable, single–ended Output Current Range 4 to 20 mA and 0 to 20 mA Output Voltage Range 0 to 10 V and –10 V to +10 V Calibration Factory calibrated to .625 μA for 0 to 20 mA; 0.5 μA for 4 to 20 mA; and .3125 mV for voltage (per count) User Supply Voltage (nominal) +24Vdc, from user supplied voltage source External Supply Voltage Range 20 Vdc to 30 Vdc range (maximum) 62 In the presence of severe RF interference (IEC 801–3, 10V/m), accuracy may be degraded to ±1% full scale (FS) for current outputs and ±3% FS for voltage outputs. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 442 Maximum Compliance Voltage VUSER –3 V (minimum) to VUSER (maximum) User Load (current mode) 0 to 850 Ω (minimum at VUSER = 20 V, maximum 1350 Ω at VUSER = 30 V) (Load less than 800 Ω is temperature dependent.) Output Load Capacitance (current mode) 2000 pF (maximum) Output Load Inductance (current mode) 1 H Output Loading (voltage mode) Output load Capacitance 5 mA (2kW minimum resistance) (1 μF maximum capacitance) Isolation, Field to Backplane (optical) and to frame ground 250 Vac continuous; 1500 Vdc for 1 minute Power Consumption 110 mA from +5Vdc PLC backplane supply 315 mA from +24Vdc user supply For product standards and general specifications, refer to Appendix A. In order to meet the IEC 1000-4-3 levels for RF Susceptibility specified in Appendix A, when this module is present, the system must be mounted in a metal enclosure. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept.
