HIMA F3209工控自动化卡件
标准和一般规范，请参考附录A59。在存在严重RF干扰（IC 801-3，10V/m）的情况下，精度可能会降低±1.5%的范围。PACSystems*RX3i系统手册第10节GFK-2314T 2019年9月模拟输入模块413 9.10.4配置：ALG608和ALG616 9.10.4.1模块参数：ALG628和ALG66参数默认描述信道值参考地址%AIxxxxx模块输入数据的起始地址。这默认为下一个可用的%AI块。信道值参考长度ALG608：16用于模块输入数据的字数。无法更改此参数。ALG616:32诊断参考地址%Ixxxxx通道诊断状态数据的起始地址。诊断参考长度0信道诊断数据所需的位参考位数。设置为0时，通道诊断被禁用。要启用通道诊断映射，请将其更改为非零值。模块状态参考地址%Ixxxxx模块状态数据的起始地址。模块状态参考长度0模块状态数据所需的位数（0到32）。设置为0时，模块状态数据的映射被禁用。要启用模块状态数据映射，请将其更改为非零值。I/O扫描集1将模块I/O状态数据分配给CPU配置中定义的扫描集。确定RX3i轮询数据输入默认强制关闭的频率。如果模块发生故障或移除，此参数指定模块所有通道值参考的状态。强制关闭=通道值清除为0。保持最后状态=频道保持其最后状态。未启用/禁用端子块的输入默认值：控制如果端子块被移除，输入是否将设置为默认值。PACSystems*RX3i系统手册第10节GFK-2314T 2019年9月模拟输入模块414参数默认描述信道故障，无端子板禁用启用/禁用：控制端子板移除后是否生成信道故障和配置的报警响应。如果禁用，则移除接线板时，通道故障和警报将被抑制。此设置不会影响模块故障，包括接线板丢失/添加故障生成。模拟输入模式单端输入模式单端口/差分：此选择必须是16位整数或32位浮点高标度值（英制单位）四个标度参数的默认值取决于配置的量程类型和量程。每个范围和范围类型都有一组不同的默认值。注：如果高量程工程单位等于高量程A/D单位，而低量程工程单位则等于低量程A/D单位时，则禁用缩放。默认值为所选范围类型的A/D上限。低量程值（工程单位）默认值为所选量程类型的低A/D限值。必须低于高缩放值。高比例值（A/D单位）默认值为所选范围类型的高A/D限制。必须大于低缩放值。低比例值
standards and general specifications, refer to Appendix A. 59 In the presence of severe RF interference (IC 801-3, 10V/m), accuracy may be degraded by ±1.5% of range. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 413 9.10.4 Configuration: ALG608 & ALG616 9.10.4.1 Module Parameters: ALG608 & ALG616 Parameter Default Description Channel Value Reference Address %AIxxxxx Starting address for the input data of the module. This defaults to the next available %AI block. Channel Value Reference Length ALG608: 16 The number of words used for the input data of the module. This parameter cannot be changed. ALG616: 32 Diagnostic Reference Address %Ixxxxx Starting address for the channel diagnostics status data. Diagnostic Reference Length 0 The number of bit reference bits required for the Channel Diagnostics data. When set to 0, Channel Diagnostics is disabled. To enable Channel Diagnostics mapping, change this to a non-zero value. Module Status Reference Address %Ixxxxx Starting address for the status data of the module. Module Status Reference Length 0 The number of bits (0 to 32) required for the Module Status data. When set to 0, mapping of Module Status data is disabled. To enable Module Status data mapping, change this to a non-zero value. I/O Scan Set 1 Assigns the module I/O status data to a scan set defined in the CPU configuration. Determines how often the RX3i polls the data Inputs Default Force Off In the event of module failure or removal, this parameter specifies the state of all Channel Value References for the module. Force Off = Channel Values clear to 0. Hold Last State = Channels hold their last state. Inputs Default w/o Terminal Block Enabled Enabled / Disabled: Controls whether inputs will be set to their defaults if the Terminal Block is removed. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 414 Parameter Default Description Channel Faults w/o Terminal Block Disabled Enabled / Disabled: Controls whether channel faults and configured alarm responses are generated after Terminal Block removal. If Disabled, channel faults and alarms are suppressed when the Terminal Block is removed. This setting does not affect module faults including the Terminal Block loss/add fault generation. Analog Input Mode Single-ended Input Mode Single-ended / Differential: This selection must 16-bit integer or 32-bit floating-point High Scale Value (Eng Units) The defaults for the four Scaling parameters depend on the configured Range Type and Range. Each Range and Range Type has a different set of defaults. Note: Scaling is disabled if both High Scale Eng. Units equals High Scale A/D Units and Low Scale Eng. Units equals Low Scale A/D Units. Default is High A/D Limit of selected range type. Low Scale Value (Eng Units) Default is Low A/D Limit of selected range type. Must be lower than the high scaling value. High Scale Value (A/D Units) Default is High A/D Limit of selected range type. Must be greater than the low scaling value. Low Scale Value
