HIMA F32100 H51A-HRS机械设备卡件
该模块可与盒型（IC694TBB032）、扩展盒型（IC 694TBB132）、弹簧型（IC6914TBS032）或扩展弹簧型（IC 6914TBS132）接线板一起使用。扩展接线板提供屏蔽布线所需的额外护罩深度。有关接线板的更多信息，请参阅第17章。接线板单独订购。这些模块必须位于RX3i通用背板中。9.10.1特点▪ 完全软件可配置，无需设置模块跳线▪ 全自动校准▪ 车载错误检查▪ 所有电压和4-20mA输入的开路检测▪ 每个通道可配置的缩放和偏移▪ 每个通道可选择高报警、低报警、高高报警、低低报警检测和报告▪ 模块故障报告▪ 支持逻辑程序中的诊断点故障触点▪ 用于未来升级的闪存▪ 正负变化率报警▪ 启动时自动校准▪ 通道报警和故障的可配置中断▪ 接线板插入或移除检测▪ 模块支持插入和取出通电的RX3i通用背板。参见第2.6.4.1节热插拔。PACSystems*RX3i系统手册第10节GFK-2314T 2019年9月模拟输入模块410 9.10.2 LED：ALG608和ALG616模块OK LED指示模块状态。现场状态LED指示至少一个通道上存在故障或接线板错误。TB（端子块）LED指示是否存在端子块。LED由背板电源总线供电。LED指示模块正常开启绿色：模块正常且已配置。绿色或琥珀色缓慢闪烁：模块正常，但未配置。快速闪烁绿色：错误。OFF：模块故障或无背板电源现场状态ON绿色：任何已启用通道上无故障，且存在接线板。ON黄色：至少一个通道出现故障。OFF：接线板不存在或未完全就位。TB ON红色：接线板不存在或未完全就位。ON绿色：存在接线板。OFF：模块没有背板电源。9.10.3及更早版本的最大4.83W-FB及更高版本的最大2.58W ALG616-EA及更早版本最大6.48W-FB和更高版本最大4.25W热降级无分辨率参考本节中的分辨率和量程类型表。输入数据格式可配置为32位字段中的浮点IEEE 32位或16位整数滤波器选项8Hz、12Hz、16Hz、40Hz、200Hz、500Hz模块扫描时间（以毫秒为单位）模块扫描最多可包含四个采集周期。每个周期包括一组特定的通道，如“通道扫描”一节所述。总扫描时间取决于扫描中的采集周期数和配置的过滤器选项。配置的滤波器编号412正常模式噪声抑制（单位：dB）50Hz 60Hz 8 Hz滤波器103 97定期校准调整。隔离电压接线板至背板/底盘光电隔离，变压器隔离250 Vac连续/1500 Vac 1分钟用于产品
This module can be used with a Box-style (IC694TBB032), Extended Boxstyle (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) terminal Block. Extended terminal blocks provide the extra shroud depth needed for shielded wiring. Refer to Chapter 17 for more information about Terminal Blocks. Terminal Blocks are ordered separately. These modules must be located in an RX3i Universal Backplane. 9.10.1 Features ▪ Completely software-configurable, no module jumpers to set ▪ Full auto-calibration ▪ On-board error-checking ▪ Open-circuit detection for all voltage and 4-20mA inputs ▪ Configurable scaling and offsets per channel ▪ High alarm, low alarm, high-high alarm, low-low alarm detection and reporting selectable per channel ▪ Module fault reporting ▪ Supports diagnostic point fault contacts in the logic program ▪ Flash memory for future upgrades ▪ Positive and negative Rate of Change Alarms ▪ Auto-calibration at startup ▪ Configurable interrupts for channel alarms and faults ▪ Terminal Block insertion or removal detection ▪ Module supports insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 410 9.10.2 LEDs: ALG608 & ALG616 The Module OK LED indicates module status. The Field Status LED indicates the presence of a fault on at least one channel or a terminal block error. The TB (Terminal Block) LED indicates the presence or absence of the terminal block. LEDs are powered by the backplane power bus. LED Indicates Module OK ON Green: Module OK and configured. Slow Flashing Green or Amber: Module OK but not configured. Quick Flashing Green: Error. OFF: Module is defective or no backplane power present Field Status ON Green: No faults on any enabled channel, and Terminal Block is present. ON Yellow: Fault on at least one channel. OFF: Terminal block not present or not fully seated. TB ON Red: Terminal block not present or not fully seated. ON Green: Terminal block is present. OFF: No backplane power to module. 9.10.3 & earlier 4.83W max -FB & later 2.58W max ALG616 -EA & earlier 6.48W max -FB & later 4.25W max Thermal De-rating None Resolution Refer to the table Resolution and Range Types in this section. Input Data Format Configurable as floating-point IEEE 32-bit or 16-bit integer in a 32-bit field Filter Options 8Hz, 12Hz, 16Hz, 40Hz, 200Hz, 500Hz Module Scan Time (in ms) The module scan can consist of up to four acquisition cycles. Each cycle includes a specific set of channels, as described in the section “Channel Scanning”. Total Scan Time depends on the number of acquisition cycles in the scan, and the configured filter option. Configured Filter Number 412 Normal Mode Noise Rejection in dB At 50Hz At 60Hz 8 Hz filter 103 97 periodic calibration adjustment. Isolation Voltage terminal block to backplane/chassis Opto-isolated, transformer isolated 250 Vac continuous/1500 Vac for 1 minute For product
