HIMA F3215A自动化模块备件
模块级诊断报告禁用（默认）或启用如果启用，则为每个活动通道分配32位数据。诊断报告和故障报告可分别为每个通道启用。PACSystems*RX3i系统手册第10节GFK-2314T 2019年9月模拟输入模块400 9.9.5.2信道配置参数：ALG233参数选择描述范围4-20 mA（默认值）、0-20 mA或4-20 mA+（增强型）在4-20 mA范围内，4至20 mA的输入电流以0至32000单位的值报告给CPU。在0至20mA范围内，0至20mA的输入电流以0至3200单位的值报告给CPU。在4至20 mA增强范围内，4至20毫安的电流以0至32000单位的值报告给CPU。低于4 mA的电流报告为负值，0表示为–8000单位。通道值格式32位浮点（默认值）或16位整数32位浮点：一个实值，范围为3.40282e+38到3.40282e+38 16位整数：32位通道数据的低位字包含16位整数通道值。高位字包含16位整数的符号。如果16位整数结果为负，则32位通道数据中的高位字设置为0xFFFF。如果16位整数结果为正，则将高位字设置为0x0000。当通道值格式参数设置为16位整数时，1000工程单位等于1.0 A/D单位。高标度值（工程单位）四个标度参数的默认值和范围取决于配置的范围类型和信道值格式。如果：高量程工程单位=高量程A/D单位，低量程工程单位/低量程A/D单位时，则禁用缩放。默认值为所选范围类型的A/D上限。当通道值格式设置为32位浮点时，范围为-3.40282e+38至3.40282e+38。对于16位整数，范围为-32768到+32767。低量程值（英制单位）高量程值（A/D单位）低量程值）正变化率极限（英制单位/秒）范围：0.0（默认值）至3.40282e+38工程单位每秒变化率，将触发正变化率报警。如果设置为0，则禁用限制。与“采样率变化率”参数一起使用。PACSystems*RX3i系统手册第10节GFK-2314T 2019年9月模拟输入模块401负变化率限值（英制单位/秒）范围：0.0（默认值）至3.40282e+38工程单位/秒变化率，将触发负变化率报警。如果设置为0，则禁用限制。与“采样率变化率”参数一起使用。变化率采样率（秒）0.0（默认值）到300.0比较之间等待的时间从0到300秒。如果设置为默认值0.0，模块将在每个输入样本后进行检查。PACSystems*RX3i系统手册第10节GFK-2314T 2019年9月模拟输入模块402信道参数（续）参数选择描述高高报警（英制单位）这些参数的默认值和范围取决于配置的范围和信道值格式。报警和死区所有报警参数均在工程单位中指定。要使用报警，必须启用诊断报告或故障报告。高-高
Module Level Diagnostic Reporting Disabled (default) or Enabled If enabled, 32 bits of data are allocated for each active channel. Diagnostic Reporting and Fault Reporting can be enabled separately for each channel. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 400 9.9.5.2 Channel Configuration Parameters: ALG233 Parameter Choices Description Range 4-20 mA (default), 0-20 mA, or 4-20 mA + (enhanced) In the 4-20 mA range, input currents from 4 to 20 mA are reported to the CPU as values from 0 to 32000 units. In the 0 to 20 mA range, input currents from 0 to 20 mA are reported to the CPU as values from 0 to 3200 units. In the 4 to 20 mA enhanced range, currents from 4 to 20 mA are reported to the CPU as values from 0 to 32000 units. Currents below 4 mA are reported as negative values with 0 represented as –8000 units. Channel Value Format 32-bit Floatingpoint (default) or 16-bit Integer 32-bit Floating-point: A real value, range 3.40282e+38 through 3.40282e+38 16-bit Integer: The low word of the 32-bit channel data contains the 16-bit integer channel value. The high word contains the sign of the 16-bit integer. If the 16-bit integer result is negative, the upper word in the 32-bit channel data is set to 0xFFFF. If the 16-bit integer result is positive, the upper word is set to 0x0000. When the Channel Value Format parameter is set to 16- bit Integer, 1000 Eng Units are equal to 1.0 A/D Unit. High Scale Value (Eng Units) The defaults and ranges for the four scaling parameters depend on the configured Range Type and Channel Value Format. Scaling is disabled if: High Scale Eng. Units = High Scale A/D Units and Low Scale Eng. Units = Low Scale A/D Units. Default is High A/D Limit of selected range type. When Channel Value Format is set to 32-bit Floatingpoint, range is -3.40282e+38 through 3.40282e+38. For 16-bit Integer, range is -32,768 through +32,767. Low Scale Value (Eng Units) High Scale Value (A/D Units) Low Scale Value (A/D Units) Positive Rate of Change Limit (Eng Units/Second) Range: 0.0 (default) through 3.40282e+38 Rate of change in Engineering Units per Second that will trigger a Positive Rate of Change alarm. If set to 0, limit is disabled. Used with “Rate of Change Sampling Rate” parameter. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 401 Negative Rate of Change Limit (Eng Units/Second) Range: 0.0 (default) through 3.40282e+38 Rate of change in Engineering Units per Second that will trigger a Negative Rate of Change alarm. If set to 0, limit is disabled. Used with “Rate of Change Sampling Rate” parameter. Rate of Change Sampling Rate (Seconds) 0.0 (default) through 300.0 Time from 0 through 300 seconds to wait between comparisons. If set to the default value of 0.0, the module checks after every input sample. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 402 Channel Parameters (Continued) Parameter Choices Description High-High Alarm (Eng Units) The defaults and ranges for these parameters depend on the configured Range and Channel Value Format. Alarms and Deadbands All of the alarm parameters are specified in Engineering Units. To use alarming, Diagnostic Reporting or Fault Reporting must be enabled. High-High
