HIMA F4110备件库存,工业备件
s–版本MA和更高版本L及更早版本不支持热插拔。IC694APU300是–修订版CA和更高版本BA和更早版本不支持热插拔。IC693APU305是IC694APU305是IC 693BEM331是MaxON冗余系统中包含的Genius总线控制器模块不应安装或从作为主机运行的PLC中移除。如果某个模块从主机中删除，然后重新安装，则在下一次备份到主机转换之前，该模块的输出将不会启用。PACSystems*RX3i系统手册第3节GFK-2314T 2019年9月安装38目录号热交换兼容说明/热交换能力限制IC694BEM331是任何时候从活动系统中移除Genius总线控制器，都有可能会中断总线，并对相应的I/O设备产生后续影响。对于需要在线维护的系统，建议使用双（冗余）Genius总线。否则，BEM331可以热交换。IC695CMM002是IC695CMM004是IC695CMX128是IC693DSM324是IC694DSM324是IC695ECM850是IC695EDS001是IC695EIS001是IC 695ETM001是IC69GCG001是Genius通信网关需要外部24Vdc电源，并且不从RX3i背板获取电源。因此，更换GCG001不会影响PLC。但是，如果不断开其电源，则无法执行此操作。如果配置为支持Genius热备用，将允许单个GCG001丢失；否则不会。IC695HSC304是IC695HSC308是IC693MDL230是IC694MDL230是IC 693MDL231是IC695MDL231是IC 694MDL240是PACSystems*RX3i系统手册第3节GFK-2314T 2019年9月安装39目录号热插拔兼容说明/在从RX3i通用背板热插拔之前移除，热插拔后重新安装。IC694MDL634是IC693MDL635是IC691MDL635是IC693M DL645是热插拔只能在现场侧接线板从模块上拆下的情况下执行。接线板符合PACSystems*RX3i系统手册第3节GFK-2314T 2019年9月安装40目录号热插拔兼容说明/热插拔能力限制IC694MDL645是的，在从RX3i通用背板热插拔之前拆除，热插拔后重新安装。IC693MDL646是热插拔只能在现场侧接线板从模块上拆下的情况下进行。在从RX3i通用背板热插拔之前拆除接线板，并在热插拔后重新安装。IC694MDL646是IC693MDL648是热插拔只能在现场侧接线板从模块上拆下的情况下执行。接线板应为IC694MDL754是IC694MDL 758是IC695MDL765是IC693MDL916是IC691MDL916是IC695PBM300是IC695PBS301是IC695PMM335是仅当PLC处于停止模式IC695PNC001是IC695PRS015是IC695PSA140是仅当冗余电源存在且每个电源都通电时才能进行热插拔。IC695PSD140是仅当存在冗余电源且每个电源都已通电时才可热插拔。IC694PSM001是PACSystems*RX3i系统手册第3节GFK-2314T 2019年9月安装42目录号热插拔兼容说明/热插拔能力限制IC695RMX128是IC695RMX228是警告在系统通电的情况下插入或移除模块可能会导致电弧。这可能会导致现场设备发生意外和潜在的危险动作。电弧在危险场所存在爆炸风险。在拆除或插入模块之前，确保该区域无危险或切断系统电源。警告：请勿在背板通电的情况下插入或移除RX3i串行扩展背板或Series 90-30扩展背板中的模块。这可能导致PLC停止或故障。可能会导致人员受伤和模块或背板损坏。如果PLC处于RUN（运行）模式，则在断电时，不会更新该背板的I/O数据。2.6.4.2不支持热插拔以下模块不支持热插入和热插拔。当机架通电时，请勿尝试插入或取出它们。
s – Revision MA & later Revision L and earlier do not support hot swap. IC694APU300 Yes – Revision CA & later Revision -BA and earlier do not support hot swap. IC693APU305 Yes IC694APU305 Yes IC693BEM331 Yes Genius Bus Controller modules that are included in a MaxON redundancy system should not be installed or removed from the PLC that is operating as a Master. If a module is removed from the Master and then re-installed, the outputs for that module will not be enabled until the next Backup-to-Master transition. PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 38 Catalog Number Hot-Swap Compatible Notes / Restrictions on Hot Swap Capability IC694BEM331 Yes Any time a Genius Bus Controller is removed from an active system, there is a possibility that the bus may be disrupted with a subsequent impact on the corresponding I/O devices. For systems that require online maintainability, it is recommended that dual (redundant) Genius busses be used. Otherwise, the BEM331 can be hot-swapped. IC695CMM002 Yes IC695CMM004 Yes IC695CMX128 Yes IC693DSM324 Yes IC694DSM324 Yes IC695ECM850 Yes IC695EDS001 Yes IC695EIS001 Yes IC695ETM001 Yes IC695GCG001 Yes The Genius Communications Gateway requires an external 24Vdc power supply and does not draw power from the RX3i backplane. Swapping out the GCG001 will therefore not impact the PLC. However, this cannot be performed without disconnecting its power supply. If configured to support Genius Hot Standby, the loss of a single GCG001 will be tolerated; otherwise not. IC695HSC304 Yes IC695HSC308 Yes IC693MDL230 Yes IC694MDL230 Yes IC693MDL231 Yes IC694MDL231 Yes IC693MDL240 Yes PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 39 Catalog Number Hot-Swap Compatible Notes / removed before hot extraction from the RX3i Universal Backplane and re-installed after hot insertion. IC694MDL634 Yes IC693MDL635 Yes IC694MDL635 Yes IC693MDL645 Yes Hot swap can only be performed with field side terminal block removed from the module. The terminal block is to PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 40 Catalog Number Hot-Swap Compatible Notes / Restrictions on Hot Swap Capability IC694MDL645 Yes be removed before hot extraction from the RX3i Universal Backplane and re-installed after hot insertion. IC693MDL646 Yes Hot swap can only be performed with field side terminal block removed from the module. The terminal block is to be removed before hot extraction from the RX3i Universal Backplane and re-installed after hot insertion. IC694MDL646 Yes IC693MDL648 Yes Hot swap can only be performed with field side terminal block removed from the module. The terminal block is to be IC694MDL754 Yes IC694MDL758 Yes IC695MDL765 Yes IC693MDL916 Yes IC694MDL916 Yes IC695PBM300 Yes IC695PBS301 Yes IC695PMM335 Yes Hot-Swap can only be performed while PLC is in STOP mode IC695PNC001 Yes IC695PRS015 Yes IC695PSA140 Yes Hot-swappable only when redundant power supplies are present and each is powered up. IC695PSD140 Yes Hot-swappable only when redundant power supplies are present and each is powered up. IC694PSM001 Yes PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 42 Catalog Number Hot-Swap Compatible Notes / Restrictions on Hot Swap Capability IC695RMX128 Yes IC695RMX228 Yes WARNING Inserting or removing a module with power applied to the system may cause an electrical arc. This can result in unexpected and potentially dangerous action by field devices. Arcing is an explosion risk in hazardous locations. Be sure that the area is non-hazardous or remove system power before removing or inserting a module. WARNING Do not insert or remove modules in RX3i Serial Expansion Backplanes or Series 90-30 Expansion Backplanes with power applied to the backplane. This could cause the PLC to stop or malfunction. Injury to personnel and damage to the module or backplane may result. If the PLC is in RUN mode, I/O data to/from this backplane will not be updated while power is removed. 2.6.4.2 Hot Insertion and Removal Not Supported The following modules do not support hot Insertion and removal. Do not attempt to insert or remove them while power is applied to the rack.
