ICS TRIPLEX T3404模块控制器
，则允许访问设置点的有效密码。1.469编程按逻辑组划分为页面。按下可循环浏览设定点页面，直到屏幕上出现所需页面。按下可进入页面。2.每一页都进一步细分为子组。按和循环浏览子组，直到屏幕上显示所需的子组。按以输入子组。3.每个子组具有一个或多个相关的设置点消息。按和循环显示设定点消息，直到出现所需的设定点消息。4.可通过按下或直到出现所需值并按下来更改大多数设定点消息。也可以通过数字键（包括小数）和按键输入数字设定点。如果输入的设定值超出范围，原始设定值将重新出现。如果输入的设定点失步，则将存储调整值（例如，对于步骤95、100、105存储为100的设定点，为101）。如果输入新值时出错，则按下可将设定点返回到其原始值。文本编辑是第3–2页第b）节：输入字母数字文本中详细描述的特殊情况。每次成功存储新设定点时，显示屏上将闪烁一条消息，说明“新设定点已存储”。5.按4、6和9键，然后按。显示以下闪烁信息：显示屏返回至6。按退出子组。多次按下将始终将光标返回到页面顶部。nn设定点nn S1 469设置n密码n[ENTER]获取更多输入密码访问：新设定点已存储设定点访问：允许的设定点消息消息消息输入消息值输入输入退出进入退出退出3-4 469电机管理继电器GE Multilin 3.2 469PC软件接口3用户界面3 3.2469PC软件界面3.2.1要求第章提供了安装和/或升级469PC软件的先前安装、升级继电器固件以及写入/编辑设定点文件所需的信息。需要注意的是，469PC软件只能用于固件版本30D220A4.000、30D220A8.000、30D251A8.000或更高版本。469PC与Mods或220之前的任何固件版本不兼容，如果编辑设置点，可能会导致错误。它可用于升级较旧版本的继电器固件，但所有先前编程的设定点将被清除。在重新编程469固件之前，确保将所有设定点保存到文件中。469PC软件必须满足以下最低要求才能在计算机上正常运行。•处理器：最低486，建议使用奔腾或更高版本•内存：最低4 MB，建议使用16 MB，最低540 K的常规内存•硬盘：安装软件前需要20 MB的可用空间。•操作系统：Windows 3.1、Windows 3.11 for Workgroups、Windows NT、，
a valid passcode to allow access to setpoints if the passcode was "469". 1. The 469 programming is broken down into pages by logical groups. Press to cycle through the setpoint pages until the desired page appears on the screen. Press to enter a page. 2. Each page is broken further into subgroups. Press and to cycle through subgroups until the desired subgroup appears on the screen. Press to enter a subgroup. 3. Each sub-group has one or more associated setpoint messages. Press and to cycle through setpoint messages until the desired setpoint message appears. 4. The majority of setpoint messages may be altered by pressing or until the desired value appears and pressing . Numeric setpoints may also be entered through the numeric keys (including decimals) and pressing . If the entered setpoint is out of range, the original setpoint value reappears. If the entered setpoint is out of step, an adjusted value will be stored (e.g. 101 for a setpoint that steps 95, 100, 105 is stored as 100). If a mistake is made entering the new value, pressing returns the setpoint to its original value. Text editing is a special case described in detail in Section b): Entering Alphanumeric Text on page 3–2. Each time a new setpoint is successfully stored, a message will flash on the display stating "NEW SETPOINT HAS BEEN STORED". 5. Press the 4, 6, and 9 keys, then press . The following flash message is displayed: and the display returns to 6. Press to exit the subgroup. Pressing numerous times will always returns the cursor to the top of the page. nn SETPOINTS nn S1 469 SETUP n PASSCODE n [ENTER] for more ENTER PASSCODE FOR ACCESS: NEW SETPOINT HASE BEEN STORED SETPOINT ACCESS: PERMITTED SETPOINT MESSAGE MESSAGE MESSAGE ENTER MESSAGE MESSAGE VALUE VALUE ENTER ENTER ESCAPE ENTER ESCAPE ESCAPE 3-4 469 Motor Management Relay GE Multilin 3.2 469PC SOFTWARE INTERFACE 3 USER INTERFACES 3 3.2469PC SOFTWARE INTERFACE 3.2.1 REQUIREMENTS This chapter provides the necessary information to install and/or upgrade a previous installation of the 469PC software, upgrade the relay firmware, and write/edit setpoint files. It should be noted that the 469PC software should only be used with firmware versions 30D220A4.000, 30D220A8.000, 30D251A8.000 or later releases. 469PC is not compatible with Mods or any firmware versions prior to 220, and may cause errors if setpoints are edited. It can be used to upgrade older versions of relay firmware, but all previously programmed setpoints will be erased. Ensure that all setpoints are saved to a file before reprogramming the 469 firmware. The following minimum requirements must be met for the 469PC software to properly operate on a computer. • Processor: minimum 486, Pentium or higher recommended • Memory: minimum 4 MB, 16 MB recommended minimum 540 K of conventional memory • Hard Drive: 20 MB free space required before installation of software. • O/S: Windows 3.1, Windows 3.11 for Workgroups, Windows NT,
