ICS TRIPLEX T3510模块备件,备件模块
装置标签详细说明了以下信息：•型号•类型•序列号•制造日期•相电流输入•特别说明•过电压类别•绝缘电压•污染程度•控制功率•输出触点额定值图2-3：外壳和装置识别标签GE Multilin 469电机管理继电器2-3 2安装2.1机械2 2.1.3安装469机箱，单独或与另一个SR系列单元相邻，可安装在标准19英寸机架的面板中（面板切口尺寸见下图）。安装前门时，必须做好准备，使其在不干扰相邻设备的情况下打开。通常情况下，469装置在出厂时安装在外壳中，在将外壳安装在支撑面板中之前，应将其拆下。下一节将描述单元的撤回。图2-4：单469和双469切割面板准备好面板中的安装孔后，从前面将469外壳滑入面板。在前面板上施加牢固的压力，以确保前挡板紧贴面板的前部，如下图所示，从外壳的每一侧弯曲一对固定凸舌（至水平位置）。机箱现已牢固安装，可用于面板布线。如果需要额外的支撑，可以订购SR可选安装套件。图2–5：弯起安装片单断流器面板双断流器面板808704A1.CDR 2-4 469电机管理继电器GE Multilin 2.1机械2安装2 2.1.4单元抽出和插入在拉出或重新插入继电器之前关闭控制电源，以防止误操作！如果试图将装置安装到不匹配的外壳中，机械钥匙将阻止装置完全插入。在以下步骤中不要用力，否则可能会造成损坏。要从机箱中卸下单元：1。抓住右侧的中心，然后拉动盖子，打开盖子，盖子将围绕左侧的铰链旋转。2.用螺丝刀向上按压锁闩，松开位于锁柄下方的锁闩。图2-6：按下锁闩以松开手柄3。将锁闩抬起时，抓住中央的锁定手柄并用力拉动，将手柄从装置底部向上旋转，直到停止移动。图2-7：旋转手柄至停止位置注意事项GE Multilin 469电机管理继电器2-5 2安装2.1机械2 4。一旦手柄从锁定机构释放，当手柄拉动时，装置可以自由滑出外壳。有时可能需要稍微调整手柄位置以释放装置。图2-8：将装置滑出外壳将装置插入外壳：1。将锁定手柄升至最高位置。2.将装置直接固定在机箱前面，并将滚动导向销（靠近锁定手柄的铰链）与机箱两侧的导向槽对齐。3.将装置滑入外壳，直到装置上的导向销
unit label details the following information: • MODEL NUMBER • TYPE • SERIAL NUMBER • MANUFACTURE DATE • PHASE CURRENT INPUTS • SPECIAL NOTES • OVERVOLTAGE CATEGORY • INSULATION VOLTAGE • POLLUTION DEGREE • CONTROL POWER • OUTPUT CONTACT RATING Figure 2–3: CASE AND UNIT IDENTIFICATION LABELS GE Multilin 469 Motor Management Relay 2-3 2 INSTALLATION 2.1 MECHANICAL 2 2.1.3 INSTALLATION The 469 case, alone or adjacent to another SR series unit, can be installed in the panel of a standard 19-inch rack (see the diagram below for panel cutout dimensions). Provision must be made when mounting for the front door to swing open without interference to, or from, adjacent equipment. Normally the 469 unit is mounted in its case when shipped from the factory, and should be removed before mounting the case in the supporting panel. Unit withdrawal is described in the next section. Figure 2–4: SINGLE AND DOUBLE 469 CUTOUT PANELS After the mounting hole in the panel has been prepared, slide the 469 case into the panel from the front. Applying firm pressure on the front to ensure the front bezel fits snugly against the front of the panel, bend out the pair of retaining tabs (to a horizontal position) from each side of the case as shown below. The case is now securely mounted, ready for panel wiring. If additional support is desired, the SR optional mounting kit may be ordered. Figure 2–5: BEND UP MOUNTING TABS Single Cutout Panel Double Cutout Panel 808704A1.CDR 2-4 469 Motor Management Relay GE Multilin 2.1 MECHANICAL 2 INSTALLATION 2 2.1.4 UNIT WITHDRAWAL AND INSERTION TURN OFF CONTROL POWER BEFORE DRAWING OUT OR RE-INSERTING THE RELAY TO PREVENT MALOPERATION! If an attempt is made to install a unit into a non-matching case, the mechanical key will prevent full insertion of the unit. Do not apply strong force in the following step or damage may result. To remove the unit from the case: 1. Open the cover by grasping the center of the right side and then pulling the cover, which will rotate about the hinges on the left. 2. Release the locking latch, located below the locking handle, by pressing upward on the latch with the tip of a screwdriver. Figure 2–6: PRESS LATCH TO DISENGAGE HANDLE 3. While holding the latch raised, grasp the locking handle in the center and pull firmly, rotating the handle up from the bottom of the unit until movement ceases. Figure 2–7: ROTATE HANDLE TO STOP POSITION CAUTION CAUTION GE Multilin 469 Motor Management Relay 2-5 2 INSTALLATION 2.1 MECHANICAL 2 4. Once the handle is released from the locking mechanism, the unit can freely slide out of the case when pulled by the handle. It may sometimes be necessary to adjust the handle position slightly to free the unit. Figure 2–8: SLIDE UNIT OUT OF CASE To insert the unit into the case: 1. Raise the locking handle to the highest position. 2. Hold the unit immediately in front of the case and align the rolling guide pins (near the hinges of the locking handle) to the guide slots on either side of the case. 3. Slide the unit into the case until the guide pins on the unit have
