ICS TRIPLEX T7150A模拟量输入模块
总实际功耗范围：0至999999.999 MW·小时。定时准确度：±0.5%更新率：5秒计量无功功耗描述：连续总无功功耗范围：0至999999.999 Mvar·小时定时准确度±0.5%更新速率：5秒测量无功发电描述：连续无功总发电范围：0到2000000.000 Mvar·时间定时准确度？.5%更新速率：需求量测量值：最大相电流3相实际功率3相视在功率3相无功功率测量类型：滚动需求间隔：5至90分钟，步长为1更新率：1分钟元素：报警其他特征跳闸前数据事件记录器跟踪存储器启动器故障模拟VT故障环境环境工作温度：-40°C至+60°C环境储存温度：-40°C至+80°C湿度：高达90%，无冷凝。海拔：高达2000米污染程度：2在低于-20°C的温度下，LCD对比度可能会受损。建议469每年至少通电一次，以防止电源中电解电容器的劣化。备用电池使用：仅当继电器无控制电源时预期寿命：≥10年，继电器无控制功率时外壳类型：完全抽出式（自动CT短路）密封：密封提供门：防尘门安装：面板或19“机架安装IP等级：IP20-X生产测试热循环：在环境温度下运行测试，降低至-40°C，然后升高至60°C介电强度：2.0 kV，持续1分钟，从继电器、CT、VT、电源到安全接地。在任何生产测试期间，请勿将过滤器接地连接到安全接地线！3 3 3 3注意事项警告1-8 469电机管理继电器GE Multilin 1.2规范第1部分简介1类型测试介电强度：根据IEC 255-5和ANSI/IEEE C37.90 2.0 kV，从继电器、CT、VT、电源到安全接地绝缘电阻：IEC255-5 500 V DC，从继电器，CT、VT，电源到安全地在介电强度或绝缘电阻测试期间，不要将过滤器接地连接到安全接地线！瞬态：ANSI C37.90.1振荡（2.5kV/1MHz）；ANSI C37.90.1快速上升（5kV/10ns）；安大略水电A-28M-82；IEC255-4脉冲/高频干扰，III级水平脉冲测试：IEC 255-5 0.5焦耳5 kV RFI:50 MHz/15 W发射器EMI:C37.90.2 150 MHz和450 MHz、10 V/m S锁定位置的电磁干扰，直到电气连接完全匹配。任何469都可以安装在任何469机箱中，但定制制造的单元除外，这些单元在机箱和单元上都有明确标识，并且配有索引销键控机构，以防止错误配对。装置安装期间无需遵守特殊通风要求。469可用湿布清洁。图2-1：尺寸为防止未经授权拆除抽出装置，可在手柄上的槽中安装导线密封。该密封件就位后，拉出装置无法拆除。密码或设定点访问跳线可用于防止输入设定点，但允许监控实际值。如果必须限制接触前面板控制装置，则可在盖子上安装单独的密封件，以防止其打开。如果产品未用于预期用途，可能会导致危险。图2-2：拉出装置上的密封警告2-2 469电机管理继电器GE Multilin 2.1机械2安装2 2.1.2产品标识每个469装置和外壳都配有永久标签。该标签安装在装置和外壳的左侧（当面向继电器前部时）。箱子标签详细说明了可以安装的装置。箱子标签详细说明了以下信息：•型号•制造日期•特别注意事项
nuous total real power consumption Range: 0 to 999999.999 MW·hours. Timing Accuracy: ±0.5% Update Rate: 5 seconds METERED REACTIVE POWER CONSUMPTION Description: Continuous total reactive power consumption Range: 0 to 999999.999 Mvar·hours Timing Accuracy: ±0.5% Update Rate: 5 seconds METERED REACTIVE POWER GENERATION Description: Continuous total reactive power generation Range: 0 to 2000000.000 Mvar·hours Timing Accuracy: ±0.5% Update Rate: 5 seconds DEMAND Metered Values: Maximum Phase Current 3 Phase Real Power 3 Phase Apparent Power 3 Phase Reactive Power Measurement Type: Rolling Demand Demand Interval: 5 to 90 minutes in steps of 1 Update Rate: 1 minute Elements: Alarm OTHER FEATURES Pre-Trip Data Event Recorder Trace Memory Starter Failure Fault Simulation VT Failure ENVIRONMENT Ambient Operating Temperature: –40°C to +60°C Ambient Storage Temperature: –40°C to +80°C Humidity: Up to 90%, non-condensing. Altitude: Up to 2000 m Pollution Degree: 2 At temperatures lower than –20°C, the LCD contrast may be impaired. It is recommended that the 469 be powered up at least once per year to prevent deterioration of electrolytic capacitors in the power supply. BATTERY BACKUP Usage: only when there is no control power to relay Life expectancy: ≥ 10 years with no control power to relay CASE Type: Fully drawout (automatic CT shorts) Seal: Seal provision Door: Dust tight door Mounting: Panel or 19" rack mount IP Class: IP20-X PRODUCTION TESTS Thermal Cycling: Operational test at ambient, reducing to –40°C and then increasing to 60°C Dielectric Strength: 2.0 kV for 1 minute from relays, CTs, VTs, power supply to Safety Ground DO NOT CONNECT FILTER GROUND TO SAFETY GROUND DURING ANY PRODUCTION TESTS! 3 3 3 3 3 3 NOTE NOTE WARNING 1-8 469 Motor Management Relay GE Multilin 1.2 SPECIFICATIONS 1 INTRODUCTION 1 TYPE TESTS Dielectric Strength: Per IEC 255-5 and ANSI/IEEE C37.90 2.0 kV for 1 minute from relays, CTs, VTs, power supply to Safety Ground Insulation Resistance: IEC255-5 500 V DC, from relays, CTs, VTs, power supply to Safety Ground DO NOT CONNECT FILTER GROUND TO SAFETY GROUND DURING DIELECTRIC STRENGTH OR INSULATION RESISTANCE TESTS! Transients: ANSI C37.90.1 Oscillatory (2.5kV/ 1MHz); ANSI C37.90.1 Fast Rise (5kV/10ns); Ontario Hydro A-28M-82; IEC255-4 Impulse/High Frequency Disturbance, Class III Level Impulse Test: IEC 255-5 0.5 Joule 5 kV RFI: 50 MHz/15 W Transmitter EMI: C37.90.2 Electromagnetic Interference at 150 MHz and 450 MHz, 10 V/m S locked position until the electrical connections are completely mated. Any 469 can be installed in any 469 case, except for custom manufactured units that are clearly identified as such on both case and unit, and are equipped with an index pin keying mechanism to prevent incorrect pairings. No special ventilation requirements need to be observed during the installation of the unit. The 469 can be cleaned with a damp cloth. Figure 2–1: DIMENSIONS To prevent unauthorized removal of the drawout unit, a wire lead seal can be installed in the slot provided on the handle. With this seal in place, the drawout unit cannot be removed. A passcode or setpoint access jumper can be used to prevent entry of setpoints but allow monitoring of actual values. If access to the front panel controls must be restricted, a separate seal can be installed on the cover to prevent it from being opened. Hazard may result if the product is not used for its intended purpose. Figure 2–2: SEAL ON DRAWOUT UNIT WARNING 2-2 469 Motor Management Relay GE Multilin 2.1 MECHANICAL 2 INSTALLATION 2 2.1.2 PRODUCT IDENTIFICATION Each 469 unit and case are equipped with a permanent label. This label is installed on the left side (when facing the front of the relay) of both unit and case. The case label details which units can be installed. The case label details the following information: • MODEL NUMBER • MANUFACTURE DATE • SPECIAL NOTES The
