ICS TRIPLEX T8230模拟量输入模块
打开469产品页面。3.单击“产品资源”列表中的“软件”项，转到469软件页面。4.将显示469PC软件的最新版本。单击469PC程序项将安装程序下载到本地PC。运行安装程序并按照提示安装到所需目录。完成后，将出现一个新的GE Power Management组窗口，其中包含469PC图标。8-4 469电机管理继电器GE Power Management 8.2配置8 469 PC软件8 8.2配置8.2.1启动和通信配置1。将运行469PC软件的计算机通过一个RS485端口（参见第2-20页第2.2.14节：RS485通信端口）或直接通过RS232前端端口连接至继电器。双击GE Power Management组中的469PC程序图标，或从Windows开始菜单中选择469PC。3.469PC软件将尝试与继电器通信。如果通信成功建立，屏幕上显示的继电器将显示与实际继电器上相同的信息。当通信建立时，显示的LED状态也将与实际继电器相匹配。4.如果469PC无法与继电器建立通信，将显示此消息。5.选择Yes（是）以编辑通信设置（或者随时选择communications（通信）>Computer（计算机）菜单项）。此时将出现COMMUNICATIONS/COMPUTER（通信/计算机）对话框，其中包含本地PC的各种通信设置。应按如下所示修改设置。图8-2：通信/计算机对话框6。要开始通信，请单击对话框通信部分中的ON按钮。状态部分指示通信状态。如果建立了通信，将显示消息“469PC现在正在与469通话”。此外，屏幕右下角的状态指示“正在通信”。GE Power Management 469电机管理继电器8-5 8 469 PC软件8.3使用469PC 8 8.3使用469PC8.3.1将设定值保存到文件中在执行任何固件升级之前，必须将设定值存储到本地PC上的文件中。在进行任何设定点更改或创建新的设定点文件之前，强烈建议保存设定点。要将设定值保存到本地PC上的文件中，请遵循以下步骤。1.选择文件>属性菜单项。出现下面的对话框，允许为469PC软件配置正确的固件版本。469PC在创建设定点文件时需要知道正确的版本，以便特定版本中不可用的设定点不会下载到继电器中。2.选择正确的固件版本后，选择文件>另存为菜单项。这将启动以下对话框。在文件名框中输入保存设定点的文件名，或选择任何显示的文件名来更新它们。所有469个设定点文件的扩展名应为469（例如，motor1.469）。单击“确定”继续。3.软件读取所有继电器设定值，并将其存储到所选文件中。8-6 469电机管理继电器GE电源管理8.3使用469PC 8 469 PC软件8 8.3.2 469固件升级在将新固件下载到469之前，有必要将469设置点保存到文件中（参见上一节）。将新固件加载到469闪存中的过程如下：1。确保本地PC通过前端RS232端口连接到469，并建立通信。将当前设定值保存到
to open the 469 product page. 3. Click the Software item from the Product Resources list to go to the 469 software page. 4. The latest version of the 469PC software will be shown. Click on the 469PC Program item to download the installation program to your local PC. Run the installation program and follow the prompts to install to the desired directory. When complete, a new GE Power Management group window will appear containing the 469PC icon. 8-4 469 Motor Management Relay GE Power Management 8.2 CONFIGURATION 8 469 PC SOFTWARE 8 8.2 CONFIGURATION 8.2.1 STARTUP & COMMUNICATIONS CONFIGURATION 1. Connect the computer running the 469PC software to the relay via one of the RS485 ports (see Section 2.2.14: RS485 COMMUNICATIONS PORTS on page 2–20) or directly via the RS232 front port. 2. Double-click the 469PC program icon within the GE Power Management group or select 469PC from the Windows Start Menu. 3. The 469PC software will attempt to communicate with the relay. If communications are successfully established, the relay shown on the screen will display the same information seen on the actual relay The LED Status shown will also match the actual relay when communications is established. 4. If 469PC cannot establish communications with the relay, this message will appear. 5. Select Yes to edit the communications settings (or alternately, select the Communications > Computer menu item at any time). The COMMUNICATIONS/COMPUTER dialog box will appear containing the various communications settings for the local PC. The settings should be modified as shown below. Figure 8–2: COMMUNICATION/COMPUTER DIALOG BOX 6. To begin communications, click the ON button in the Communication section of the dialog box. The status section indicates the communications status. If communications are established, the message “469PC is now talking to a 469” is displayed. As well, the status at the bottom right hand corner of the screen indicates “Communicating”. GE Power Management 469 Motor Management Relay 8-5 8 469 PC SOFTWARE 8.3 USING 469PC 8 8.3 USING 469PC 8.3.1 SAVING SETPOINTS TO A FILE Setpoints must be saved to a file on the local PC before performing any firmware upgrades. Saving setpoints is also highly recommended before making any setpoint changes or creating new setpoint files. To save setpoints to a file on the local PC, follow the procedure below. 1. Select the File > Properties menu item. The dialog box below appears, allowing for the configuration of the 469PC software for the correct firmware version. 469PC needs to know the correct version when creating a setpoint file so that setpoints not available in a particular version are not downloaded into the relay. 2. When the correct firmware version is chosen, select the File > Save As menu item. This launches the following dialog box. Enter the filename under which the setpoints are saved in the File Name box or select any displayed file names to update them. All 469 setpoint files should have the extension 469 (for example, motor1.469). Click OK to proceed. 3. The software reads all the relay setpoint values and stores them to the selected file. 8-6 469 Motor Management Relay GE Power Management 8.3 USING 469PC 8 469 PC SOFTWARE 8 8.3.2 469 FIRMWARE UPGRADES Prior to downloading new firmware to the 469, it is necessary to save the 469 setpoints to a file (see the previous section). Loading new firmware into the 469 flash memory is accomplished as follows: 1. Ensure the local PC is connected to the 469 via the front RS232 port and that communications are established. Save the current setpoints to a
