ICS TRIPLEX T8870工控备件机器人模块
远程跳闸压力开关。报警控制断电速度开关跳闸振动开关。报警控制电源应用减载跳闸计数器报警紧急关闭压力开关。跳闸转速表报警紧急响应。打开振动开关跳闸通用开关A报警启动，同时阻止转速表跳闸通用开关B报警469未插入通用开关A跳闸通用开关C报警模拟启动通用开关B跳闸通用开关D报警模拟停止通用开关C跳闸热模型报警强制继电器通用开关D跳闸过载报警过载跳闸欠电流报警短路跳闸电流U/B报警短路备用接地故障报警机械堵塞跳闸定子RTD 1报警欠电流跳闸定子RTD 2报警电流U/B跳闸定子RTD 3报警接地故障跳闸定子RTD 4报警接地错误备用定子RTD 5报警差动跳闸定子RTD 6报警加速跳闸轴承RTD 7报警定子RTD 1跳闸轴承RTD 8报警定子RTD 2跳闸轴承RTD 9报警定子RTD 3跳闸轴承RTD10报警定子RTD 4跳闸RTD11报警定子RTD 5跳闸环境RTD12报警定子RTD 6跳闸打开RTD报警轴承RTD 7跳闸短路/低RTD报警轴承RTD8跳闸欠压报警轴承RTD 9跳闸过压报警轴承RTD10跳闸电压。频率报警RTD11跳闸无功功率报警环境RTD12跳闸欠功率报警欠电压跳闸计数器报警过压跳闸线圈超相反向跳闸焊接接触器电压。频率跳闸断路器故障无功跳闸电流需求报警功率因数跳闸kW需求报警功率不足跳闸kvar需求报警模拟I/P 1至4跳闸kVA需求报警单相（不平衡）模拟I/P 1-4报警过转矩5-26 469电机管理继电器GE Power Management 5.7 A6产品信息5实际值5 5.7 A6产品数据5.7.1 469型号信息469型号的所有型号当单元通电时，可以在此处查看信息。如果出现产品软件升级或服务问题，在进行任何查询之前，应记下此处显示的信息。5.7.2校准信息原始校准日期和GE Power Management 469电机管理继电器5-29 5实际值5.8诊断5•请输入非零密码：如果密码为零，则密码安全功能被禁用。如果更改密码设置点输入为“是”，则会出现此闪烁消息，提示用户输入非零密码，从而启用该功能。•现在允许设置点访问：该闪光消息通知用户，设置点现在可以在启用密码安全功能并输入有效密码时更改和存储。•设定点访问现在受限：如果密码安全功能已启用，输入了有效的密码，并且S1 469设置/密码/设定点访问设定值受限，则显示此消息。只要允许访问设定点并且移除了访问跳线，该消息也会出现。•日期输入未完成：由于日期设置点具有特殊格式（MM/DD/YYYY），如果在输入完整值之前按下，则会显示此消息，并且不会存储新值。必须使用完整的信息进行另一次尝试。•DATE ENTRY WAS OUT RANGE（日期输入超出范围）：如果输入的日期无效（例如，输入的月份为15），则显示此消息。•时间输入未完成：
Remote Trip Pressure Sw. Alarm Control Power Lost Speed Switch Trip Vibration Sw. Alarm Control Power Applied Load Shed Trip Counter Alarm Emergency Rst.Close Pressure Sw. Trip Tachometer Alarm Emergency Rst. Open Vibration Sw.Trip General Sw.A Alarm Start While Blocked Tachometer Trip General Sw.B Alarm 469 Not Inserted General Sw.A Trip General Sw.C Alarm Simulation Started General Sw.B Trip General Sw.D Alarm Simulation Stopped General Sw.C Trip Thermal Model Alarm Forced Relay General Sw.D Trip Overload Alarm Overload Trip Undercurrent Alarm Short Circuit Trip Current U/B Alarm Short Circuit Backup Ground Fault Alarm Mechanical Jam Trip Stator RTD 1 Alarm Undercurrent Trip Stator RTD 2 Alarm Current U/B Trip Stator RTD 3 Alarm Ground Fault Trip Stator RTD 4 Alarm Ground Fault Backup Stator RTD 5 Alarm Differential Trip Stator RTD 6 Alarm Acceleration Trip Bearing RTD 7 Alarm Stator RTD 1 Trip Bearing RTD 8 Alarm Stator RTD 2 Trip Bearing RTD 9 Alarm Stator RTD 3 Trip Bearing RTD10 Alarm Stator RTD 4 Trip RTD11 Alarm Stator RTD 5 Trip Ambient RTD12 Alarm Stator RTD 6 Trip Open RTD Alarm Bearing RTD 7 Trip Short/Low RTD Alarm Bearing RTD 8 Trip Undervoltage Alarm Bearing RTD 9 Trip Overvoltage Alarm Bearing RTD10 Trip Volt. Frequency Alarm RTD11 Trip Reactive Power Alarm Ambient RTD12 Trip Underpower Alarm Undervoltage Trip Trip Counter Alarm Overvoltage Trip Trip Coil Super Phase Reversal Trip Welded Contactor Volt. Frequency Trip Breaker Failure Reactive Power Trip Current Demand Alarm Power Factor Trip kW Demand Alarm Underpower Trip kvar Demand Alarm Analog I/P 1 to 4 Trip kVA Demand Alarm Single Phasing (Unbalanced) Analog I/P 1 to 4 Alarm Overtorque 5-26 469 Motor Management Relay GE Power Management 5.7 A6 PRODUCT INFO 5 ACTUAL VALUES 5 5.7 A6 PRODUCT INFO 5.7.1 469 MODEL INFO All of the 469 model information may be viewed here when the unit is powered up. In the event of a product software upgrade or service question, the information shown here should be jotted down prior to any inquiry. 5.7.2 CALIBRATION INFO The date of the original calibration and GE Power Management 469 Motor Management Relay 5-29 5 ACTUAL VALUES 5.8 DIAGNOSTICS 5 • PLEASE ENTER A NON-ZERO PASSCODE: If the passcode is zero, the passcode security feature is disabled. If the Change Passcode Setpoint is entered as yes, this flash message will appear prompting the user to enter a non-zero passcode which in turn will enable the feature. • SETPOINT ACCESS IS NOW PERMITTED: This flash message notifies the user that setpoints may now be altered and stored any time the passcode security feature is enabled and a valid passcode is entered. • SETPOINT ACCESS IS NOW RESTRICTED: This message appears if the passcode security feature is enabled, a valid passcode has been entered, and the S1 469 SETUP / PASSCODE / SETPOINT ACCESS setpoint value is Restricted. This message also appears anytime that setpoint access is permitted and the access jumper is removed. • DATE ENTRY WAS NOT COMPLETE: Since the DATE setpoint has a special format (MM/DD/YYYY), if is pressed before the complete value is entered, this message appears and the new value is not stored. Another attempt will have to be made with the complete information. • DATE ENTRY WAS OUT OF RANGE: This message appears if and invalid entry is made for the DATE (e.g. 15 entered for month). • TIME ENTRY WAS NOT COMPLETE:
