IS200ATBAG1 IS200ATBAG1BAA1输出卡件,工业卡件
发动机探头可由输入开关电源的+24 V供电。NPN晶体管输出可被带到配置为转速表的可分配开关输入之一。额定转速：3600 RPM范围：100至7200 RPM，步骤：1转速表报警：关闭范围：关闭、锁定、未锁定分配报警继电器：报警范围：报警、报警和辅助2、报警和辅2和辅3、报警和副3、辅助2、辅2和辅助3、辅助3转速表报警速度：10%额定范围：5至100%，步骤：2转速表报警延迟：1秒范围：1至250秒。，步骤：1转速表报警事件：关闭范围：打开，关闭转速表跳闸：关闭范围；关闭，锁定，未锁定分配跳闸继电器：跳闸范围：跳闸，跳闸和辅助2，跳闸&辅助2和辅助3，跳闸与辅助3转速表跳闸速度：10%额定范围：5%至95%，步骤：1测速计跳闸延迟：1秒范围：1至250秒。，步骤：1 MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESTAGE ESCAPE MESSAGE ESC APE MESPAGE ESCAP MESSAGE ESCAPE GE Power Management 469电动机管理继电器4-23 4设定点编程4.4 S3数字输入4 4.4.18数字输入功能：通用开关A-D有四个通用开关功能可分配给四个可分配数字输入。一旦为其中一个数字输入选择了通用开关功能，此处显示的设置点消息将跟随分配消息。然后可以为该输入配置警报和/或跳闸。如果需要，可为警报和/或跳闸分配一个通用名称和一个从电机启动开始的通用阻断时间（如果在电机启动后一段时间内禁用警报）。BLOCK TIME的值为“0”表示当电机停止或运行时，该功能始终处于激活状态。开关也可以定义为常开或常闭。块延迟到期后，将监控数字输入。如果开关在指定延迟后未处于正常状态，则会发生报警或跳闸。4.4.19数字输入功能：捕获跟踪此设置允许用户通过开关输入根据命令捕获跟踪。然后可以使用469PC软件显示捕获的波形。4.4.20数字输入功能：模拟预故障此设置允许用户通过开关输入启动S13中编程的模拟预故障模式。这通常用于继电器或系统测试。4.4.21数字输入功能：模拟故障此设置允许用户通过开关输入启动S13中编程的模拟故障模式。这通常用于继电器或系统测试。4.4.22数字输入功能：模拟预故障…故障此设置允许用户通过开关输入启动S13中编程的模拟预故障到故障模式。这通常用于继电器或系统测试。开关名称：通用开关。A范围：12个字母数字字符通用开关A：常开范围：常开，常闭，从启动输入：0 s范围：0到5000秒，步骤1（0表示电机停止运行时功能激活）通用开关A报警：关闭范围：关闭，锁定，未锁定分配报警继电器：报警范围：报警，报警&motor. The probe could be powered from the +24 V from the input switch power supply. The NPN transistor output could be taken to one of the assignable switch inputs configured as a tachometer. RATED SPEED: 3600 RPM Range: 100 to 7200 RPM, step: 1 TACHOMETER ALARM: Off Range: Off, Latched, Unlatched ASSIGN ALARM RELAYS: Alarm Range: Alarm, Alarm & Auxiliary2, Alarm & Aux2 & Aux3, Alarm & Auxiliary3, Auxiliary2, Aux2 & Aux3, Auxiliary3 TACHOMETER ALARM SPEED: 10% Rated Range: 5 to 100%, step: 1 TACHOMETER ALARM DELAY: 1 s Range: 1 to 250 sec., step:1 TACHOMETER ALARM EVENTS: Off Range: On, Off TACHOMETER TRIP: Off Range: Off, Latched, Unlatched ASSIGN TRIP RELAYS: Trip Range: Trip, Trip & Auxiliary2, Trip & Aux2 & Aux3, Trip & Auxiliary3 TACHOMETER TRIP SPEED: 10% Rated Range: 5 to 95%, step: 1 TACHOMETER TRIP DELAY: 1 s Range: 1 to 250 sec., step: 1 MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE GE Power Management 469 Motor Management Relay 4-23 4 SETPOINT PROGRAMMING 4.4 S3 DIGITAL INPUTS 4 4.4.18 DIGITAL INPUT FUNCTION: GENERAL SWITCH A-D There are four General Switch functions assignable to any of the four assignable digital inputs. Once a General Switch function is chosen for one of the digital inputs, the setpoint messages shown here follow the assignment message. An alarm and/or trip may then be configured for that input. The alarm and/or trip may be assigned a common name and a common block time from motor start if required (if the alarm is to be disabled until some period of time after he motor has been started). A value of "0" for the BLOCK TIME indicates that the feature is always active, when the motor is stopped or running. The switch may also be defined as normally open or normally closed. After the block delay has expired, the digital input will be monitored. If the switch is not in its normal state after the specified delay, an alarm or trip will occur. 4.4.19 DIGITAL INPUT FUNCTION: CAPTURE TRACE This setting allows the user to capture a trace upon command via a switch input. The captured waveforms can then be displayed with the 469PC software. 4.4.20 DIGITAL INPUT FUNCTION: SIMULATE PRE-FAULT This setting allows the user to start Simulate Pre-Fault mode as programmed in S13 via a switch input. This is typically used for relay or system testing. 4.4.21 DIGITAL INPUT FUNCTION: SIMULATE FAULT This setting allows the user to start Simulate Fault mode as programmed in S13 via a switch input. This is typically used for relay or system testing. 4.4.22 DIGITAL INPUT FUNCTION: SIMULATE PRE-FAULT…FAULT This setting allows the user to start Simulate Pre-Fault to Fault mode as programmed in S13 via a switch input. This is typically used for relay or system testing. SWITCH NAME: General Sw. A Range: 12 alphanumeric characters GENERAL SWITCH A: Normally Open Range: Normally Open, Normally Closed BLOCK INPUT FROM START: 0 s Range: 0 to 5000 sec., step 1 (0 indicates that feature is active while motor is stopped as well as running) GENERAL SWITCH A ALARM: Off Range: Off, Latched, Unlatched ASSIGN ALARM RELAYS: Alarm Range: Alarm, Alarm &
