IS200DSVOH1ABA工控模块卡件
远程端口4001默认设置为指示对等UDP主机的UDP端口。值范围：1～65535串行端口SPort-0默认设置为将UDP主机应用于选定的串行端口。每个串行端口最多可以同时支持4个UDP服务器。默认情况下，定义启用未选中选中启用框以启用规则。保存单击保存保存设置撤消单击撤消取消设置EW200工业蜂窝网关182启用RFC-2217模式RFC-2217定义了基于Telnet协议的通用COM端口控制选项。使用RFC-2217模式，远程主机可以监视和管理远程串行连接的设备，就像它们连接到本地串行端口一样。在本地串行设备上创建虚拟串行端口时，需要指定远程主机的IP地址以建立连接。启用RFC-2217模式窗口项值设置描述操作模式所需设置选择RFC-2217方式。默认设置侦听端口4001指示RFC-2217连接的侦听端口。值范围：1~65535默认设置为“全部允许”信任类型。选择“全部允许所有客户端连接”。否则，选择“特定IP”以限制某些客户端。连接空闲超时0默认设置为输入空闲超时（分钟）。空闲超时用于在空闲时间过去后断开连接。值范围：0~60分钟。活动检查超时0默认设置为输入活动检查超时的时间段。如果活动检查的响应时间长于此超时设置，则连接将被终止。值范围：0~60分钟。启用默认情况下未选中选中启用框以在指定的操作模式下激活相应的串行端口。保存单击保存保存设置撤消单击撤消取消设置EW200 Industrial Cellular Gateway 183指定远程主机进行访问如果您选择了特定IP作为信任类型，则会显示“受信任的IP定义”窗口。这些设置对TCP服务器和RFC-2217模式都有效。指定RFC-2217客户端用于访问窗口项值设置描述主机所需设置输入允许的客户端的IP地址范围。默认情况下未选中串行端口选中该复选框可为所选串行端口指定规则。定义默认情况下启用未选中选中启用复选框可启用规则。保存单击保存以保存设置撤消单击撤消以取消设置Con VirtualCOM数据日志如果您想监视串行端口的流量，可以更改数据日志设置并使其能够获取流量日志。EW200 Industrial Cellular Gateway 184 COM Logging Configuration Window Item Value setting Description Storage Device（EW200工业蜂窝网关184 COM日志记录配置窗口项值设置描述存储设备）默认未选中选中Enable（启用）复选框，并使用连接的可用存储（USB或SD卡）设备将数据日志文件保存在文件夹“\virtual COM log\SPortn\$Date\”下。
Remote Port 4001 is set by default Indicate the UDP port of peer UDP hosts. Value Range: 1 ~ 65535 Serial Port SPort-0 is set by default Apply the UDP hosts for a selected serial port. Up to 4 UDP servers can be cond at the same time for each serial port. Definition Enable Unchecked by default Check the Enable box to enable the rule. Save Click Save to save the settings Undo Click Undo to cancel the settings EW200 Industrial Cellular Gateway 182 Enable RFC-2217 Mode RFC-2217 defines general COM port control options based on the Telnet protocol. With the RFC-2217 mode, a remote host can monitor and manage remote serially attached devices as though they were connected to the local serial port. When a virtual serial port on the local serial device is being created, it is required to specify the IP-address of the remote hosts to establish connection with. Enable RFC-2217 Mode Window Item Value setting Description Operation Mode Required setting Select RFC-2217 mode. Listen Port 4001 is set by default Indicate the listening port of RFC-2217 connection. Value Range: 1 ~ 65535 Trust Type Allow All is set by default Choose Allow All to allow any clients to connect. Otherwise choose Specific IP to limit certain clients. Connection Idle Timeout 0 is set by default Enter the idle timeout in minutes. The idle timeout is used to disconnect the connection when the idle time has elapsed. Value Range: 0 ~ 60 minutes. Alive Check Timeout 0 is set by default Input the time period of alive-check timeout. The connection will be terminated if response time of alive-check is longer than this timeout setting. Value Range: 0 ~ 60 minutes. Enable Unchecked by default Check the Enable box to activate the corresponding serial port in specified operation mode. Save Click Save to save the settings Undo Click Undo to cancel the settings EW200 Industrial Cellular Gateway 183 Specify Remote Host for Access If you selected Specific IPs as the trust Type, the Trusted IP Definition window appears. The settings are valid for both TCP Server and RFC-2217 modes. Specify RFC-2217 Clients for Access Window Item Value setting Description Host Required setting Enter the IP address range of allowed clients. Serial Port Unchecked by default Check the box to specify the rule for selected Serial Port. Definition Enable Unchecked by default Check the Enable box to enable the rule. Save Click Save to save the settings Undo Click Undo to cancel the settings Con VirtualCOM Data Logging If you intend to monitor the traffic of the serial port, you can con the data logging settings and enable it to get the traffic log consequently. EW200 Industrial Cellular Gateway 184 COM Logging Configuration Window Item Value setting Description Storage Device Unchecked by default Check the Enable box and use the attached available storage (USB or SD-card) device to keep the data log file under the folder “\virtual-com-log\SPortn\$Date\”.
