IS200EXTBG1A处理器模块
Fair Rite Products卡扣式铁氧体抑制芯（43型材料）或同等产品（进出EMI/RFI机柜的每根电缆都需要单独的卡扣式过滤器）火灾和气体检测应用对于所有火灾和气体探测应用，请参阅Tricon v9–v10系统的Tricon安全注意事项指南，了解更多安装指南。对于火灾和气体探测应用，必须使用冗余的现场和系统电源和/或电源。功能安全应用对于所有功能安全应用，请参阅Tricon v9–v10系统的Tricon安全注意事项指南，了解更多安装指南。核1E应用对于所有核1E应用，请联系IPS全球客户支持（GCS）中心以获取最新的详细安装说明。只能使用符合核1E应用要求的模块；有关核合格设备清单（NQEL）上的最新项目，请联系IPS全球客户支持（GCS）中心。安装指南177 Tricon v9–v10 Systems半导体制造-健康和安全应用半导体制造应用的规划和安装指南，强烈建议遵守这些附加安装指南：•根据IEC 61010-1的要求，应批准现场和逻辑电源用于安全超低压（SELV）电路。•对于电压大于30 Vrms/36 VDC的装置，控制器和相关设备必须安装在一个上锁的机柜中，仅限经过培训的人员进入，并在显眼位置贴上危险电压警告标签对于环境温度超过94°F（35°C）的安装，控制器和相关设备应安装在一个上锁的机柜中，仅限经过培训的人员进入，并在显眼位置贴上热表面警告标签对于必须确保系统连续、正确运行的应用，控制器和相关设备应安装在一个上锁的机柜中，仅限经过培训的人员进入，并在显眼位置贴上一般危险警告标签。有关标签的物理描述，请参阅附录C“警告标签”。178第3章Tricon v9–v10系统的安装和维护规划与安装指南机箱和模块安装本节介绍如何安装机箱、模块和其他Tricon组件。打开Tricon控制器的包装时，根据装运清单检查包装中的物品，以确认您订购的所有物品都包含在内。保管好箱子和包装材料，以防因任何原因需要将物品退还给Triconex。主题包括：•第179页上的机箱后部安装•第179页面上的机箱机架安装•第180页上的安装尺寸和间隙•第181页上的对流冷却允许•第181页面上的连接多个机箱•第181张上的插槽盖•第182页上的机架I/O总线地址•第184页上的电源模块安装•第186页•第191页上设置MP节点设置•第192页上安装模块•第192页面上数字输出现场接线注意事项•第193页上脉冲输入安装和操作•第194页上脉冲输出累加器安装和操作→第194页中热电偶输入安装和运行•第194页面上安装3807型双极模拟输出模块•在第195页的8121型增强型低密度扩展机箱中安装HART接口模块•在第199页的v6–v8升级系统中安装HART界面模块•第202页的机箱封装警告对于ATEX应用，外ELCO连接器必须安装垫圈，
Fair-Rite Products snap-on ferrite suppression cores (type 43 material) or equivalent (a separate snap-on filter is required for each cable entering or leaving the EMI/RFI cabinet) Fire and Gas Detection Applications For all fire and gas detection applications, refer to the Tricon Safety Considerations Guide for Tricon v9–v10 Systems for additional installation guidelines. For fire and gas detection applications, redundant field and system power sources and/or supplies must be used. Functional Safety Applications For all functional safety applications, refer to the Tricon Safety Considerations Guide for Tricon v9– v10 Systems for additional installation guidelines. Nuclear 1E Applications For all nuclear 1E applications, contact the IPS Global Client Support (GCS) center for the latest detailed installation instructions. Only those modules qualified for nuclear 1E applications can be used; contact the IPS Global Client Support (GCS) center for the latest items on the Nuclear Qualified Equipment List (NQEL). Installation Guidelines 177 Planning and Installation Guide for Tricon v9–v10 Systems Semiconductor Manufacturing - Health and Safety Applications For semiconductor manufacturing applications, compliance with these additional installation guidelines is highly recommended: • Field and logic power supplies should be approved for use in safety extra-low-voltage (SELV) circuits according to the requirements of IEC 61010-1. • For installations with voltages greater than 30 Vrms/36 VDC, the controller and associated equipment must be installed in a locked cabinet restricting access to trained personnel only, with a hazardous-voltage warning label attached prominently. • For installations with ambient temperatures exceeding 94° F (35° C), the controller and associated equipment should be installed in a locked cabinet restricting access to trained personnel only, with a hot-surface warning label attached prominently. • For applications in which continuous, correct system operation must be assured, the controller and associated equipment should be installed in a locked cabinet restricting access to trained personnel only, with a general-hazard warning label attached prominently. For a physical description of labels, see Appendix C, Warning Labels. 178 Chapter 3 Installation and Maintenance Planning and Installation Guide for Tricon v9–v10 Systems Chassis and Module Installation This section explains how to mount the chassis, modules, and other Tricon components. When unpacking the Tricon controller, check the items in the package against the shipping list to verify that everything you ordered is included. Keep the boxes and packing materials in case you need to return items to Triconex for any reason. Topics include: • Rear-Mounting the Chassis on page 179 • Rack-Mounting the Chassis on page 179 • Dimensions and Clearances for Installation on page 180 • Allowing for Convection Cooling on page 181 • Connecting Multiple Chassis on page 181 • Using Slot Covers on page 181 • I/O Bus Address of Chassis on page 182 • Power Module Installation on page 184 • Slot Keys for Modules on page 186 • Setting the MP Node Setting on page 191 • Installing Modules on page 192 • Digital Output Field Wiring Precautions on page 192 • Pulse Input Installation and Operation on page 192 • Pulse Input Totalizer Installation and Operation on page 193 • Thermocouple Input Installation and Operation on page 194 • Installing Model 3807 BiPolar Analog Output Modules on page 194 • Installing HART Interface Modules in the Model 8121 Enhanced Low Density Expansion Chassis on page 195 • Installing HART Interface Modules in Systems Upgraded from v6–v8 on page 199 • Enclosing the Chassis on page 202 WARNING For ATEX applications, male ELCO connectors must have a gasket installed,
