IS200HSLAH2ADE工控模块机器人备件
2.最大输出切换率可实现I/O诊断的正确操作和所有正常可检测故障的检测。最小切换率提供了模块计算平均故障间隔时间（MTBF）10%内正常不可检测故障的故障覆盖率。每100毫秒加一次扫描不需要诊断故障持续时间3 3。使用OVD禁用功能可以禁用诊断故障。2 ms，最大导通状态压降：背板处<0.5 VDC典型@250mA<0.5 VDC最大@1A导通状态电压降：带外部终端，10英尺电缆<2 VDC典型@250 mA<3 VDC最大@1 A导通状态：带外部端接，99英尺电缆<3 VDC典型@250mA<6 VDC最大@1A感应反冲保护（反EMF）I/O模块上的反向二极管数字输出模块95 Tricon v9–v10系统3603E和3603T规格规划和安装指南本表列出了3603E型和3603TT型的规格，它们是标称电压为120 VDC的TMR数字输出模块。警告：3603B、3603E和3603T型数字输出模块不应混合在同一逻辑插槽中。Triconex强烈建议您在选择3603T型模块用于具有以下任何一项的应用之前进行兼容性测试：•现场布线长度超过328英尺（100米）•非双绞线电缆•非典型负载，如智能设备、闪光灯、，当与1600米电缆和低功率电磁阀一起使用时，型号3603T或klaxons可能会出现输出表决器诊断（OVD）故障。表33 3603E和3603T数字输出规格特性规格颜色代码钢蓝色输出信号数量16，公共电压范围90–150 VDC最大电压160 VDC逻辑功率<10瓦额定电流，最大0.8安培/点，4安培浪涌/10毫秒负载泄漏电流2 mA，最大保险丝（现场终端模块）每个输出1个（1安培，快速作用）状态指示器：开或关状态每个点1个状态指示器：模块状态通过，故障，活动状态指示灯：现场报警1负载/保险丝点隔离：3603E 1500 VDC最小点隔离：36003T 2500 VDC最小输出诊断故障覆盖范围2：最大输出切换率最小输出切换率每100毫秒加一次扫描不需要诊断故障持续时间3 2毫秒，最大值，500μ秒，典型的通态压降：在背板<0.5 VDC典型@250 mA<0.5 VDC最大@1A 96第2章Tricon v9–v10系统3604E规格系统组件规划和安装指南本表列出了3604E型号的规格，该型号是一个标称电压为24 VDC的TMR数字输出模块。导通状态压降：带外部终端，10英尺电缆<1.5 VDC，典型@250mA<2.5 VDC，最大@1A导通状态电压降：带外部端接，99英尺电缆<2.5 VDC（典型@250 mA<5.5 VDC，最大值@1A）感应反冲保护（反EMF）输入/输出模块1上的反向二极管。必须向所有点供电，包括非公用面板上未使用的点。2.最大输出切换率可实现I/O诊断的正确操作和所有正常可检测故障的检测。最小切换率提供了模块计算平均故障间隔时间（MTBF）10%内正常不可检测故障的故障覆盖率。3.可使用OVD禁用功能禁用诊断故障。表34 3604E数字输出规格特性规格颜色代码深蓝色输出信号数量16，非公共电压范围22–45 VDC逻辑功率<10瓦额定电流，最大2安培/点，10安培浪涌/10毫秒负载泄漏电流2 mA，最大保险丝（现场终端模块）每个输出1个（2.5安培快速作用）状态指示器：开或关状态每个点1个状态指示器：模块状态通过、故障、，活动状态指示灯：现场报警1负载/保险丝点隔离1500 VDC最小输出诊断故障范围2：最大输出切换率最小输出切换率每100毫秒加一次扫描不适用诊断故障持续时间3最大2毫秒，500μs典型导通状态压降：在背板<3 VDC典型@500mA<3 VDC最大@2A表33 3603E和3603T数字输出规格（续）功能规格数字输出模块97 Tricon v9–v10系统规划和安装指南3607E规格本表列出了3607E型的规格，其为标称电压为48VDC的TMR数字输出模块。通态压降：带外部终端，10英尺电缆<4 VDC，典型@500mA<5 VDC最大值
2. The maximum output toggle rate enables proper operation of I/O diagnostics and detection of all normally detectable faults. The minimum toggle rate provides fault coverage of normally undetectable faults within 10% of the calculated mean-time-between-faults (MTBF) for the module. Every 100 ms plus one scan Not required Diagnostic glitch duration3 3. Diagnostic glitching can be disabled by using the OVD disable function. 2 ms, maximum On-state voltage drop: At backplane < 0.5 VDC typical @ 250mA < 0.5 VDC maximum @ 1A On-state voltage drop: With external termination, 10-foot cable < 2 VDC typical @ 250mA < 3 VDC maximum @ 1A On-state voltage drop: With external termination, 99-foot cable < 3 VDC typical @ 250mA < 6 VDC maximum @ 1A Inductive kick-back protection (reverse EMF) Reverse diode on I/O module Digital Output Modules 95 Planning and Installation Guide for Tricon v9–v10 Systems 3603E and 3603T Specifications This table lists the specifications for models 3603E and 3603T, which are TMR Digital Output Modules with a nominal voltage of 120 VDC. CAUTION Model 3603B, 3603E, and 3603T Digital Output Modules should not be mixed in the same logical slot. Triconex highly recommends that you perform compatibility testing before selecting the model 3603T module for use in applications that have any of the following: • field wiring lengths over 328 feet (100 meters) • cable that is not twisted pair • atypical loads such as smart devices, strobe lights, or klaxons Model 3603T may experience Output Voter Diagnostic (OVD) failures when used with a 1600 meter cable and a low-watt solenoid. Table 33 3603E and 3603T Digital Output Specifications Feature Specification Color code Steel blue Number of output signals 16, commoned Voltage range 90–150 VDC Maximum voltage 160 VDC Logic power < 10 watts Current ratings, maximum 0.8 amp/point, 4 amps surge/10 ms Leakage current to load 2 mA, maximum Fuses (field termination module) 1 per output (1 amp, fast-acting) Status indicator: On or Off state 1 per point Status indicator: Module status Pass, Fault, Active Status indicator: Field alarm1 Load/Fuse Point isolation: 3603E 1500 VDC minimum Point isolation: 3603T 2500 VDC minimum Output diagnostic fault coverage2: Maximum output toggle rate Minimum output toggle rate Every 100 ms plus one scan Not required Diagnostic glitch duration3 2 ms, maximum, 500 μsec, typical On-state voltage drop: At backplane < 0.5 VDC typical @ 250mA < 0.5 VDC maximum @ 1A 96 Chapter 2 System Components Planning and Installation Guide for Tricon v9–v10 Systems 3604E Specifications This table lists the specifications for model 3604E, which is a TMR Digital Output Module with a nominal voltage of 24 VDC. On-state voltage drop: With external termination, 10-foot cable < 1.5 VDC typical @ 250mA < 2.5 VDC maximum @ 1A On-state voltage drop: With external termination, 99-foot cable < 2.5 VDC typical @ 250mA < 5.5 VDC maximum @ 1A Inductive kick-back protection (reverse EMF) Reverse diode on I/O module 1. Power must be supplied to all points, including unused points on non-commoned panels. 2. The maximum output toggle rate enables proper operation of I/O diagnostics and detection of all normally detectable faults. The minimum toggle rate provides fault coverage of normally undetectable faults within 10% of the calculated mean-time-between-faults (MTBF) for the module. 3. Diagnostic glitching can be disabled by using the OVD disable function. Table 34 3604E Digital Output Specifications Feature Specification Color code Dark blue Number of output signals 16, non-commoned Voltage range 22–45 VDC Logic power < 10 watts Current ratings, maximum 2 amps/point, 10 amps surge/10 ms Leakage current to load 2 mA, maximum Fuses (field termination module) 1 per output (2.5 amps fast-acting) Status indicator: On or Off state 1 per point Status indicator: Module status Pass, Fault, Active Status indicator: Field alarm1 Load/Fuse Point isolation 1500 VDC minimum Output diagnostic fault coverage2: Maximum output toggle rate Minimum output toggle rate Every 100 ms plus one scan Not applicable Diagnostic glitch duration3 2 ms maximum, 500 μs typical On-state voltage drop: At backplane < 3 VDC typical @ 500mA < 3 VDC maximum @ 2A Table 33 3603E and 3603T Digital Output Specifications (continued) Feature Specification Digital Output Modules 97 Planning and Installation Guide for Tricon v9–v10 Systems 3607E Specifications This table lists the specifications for model 3607E, which is TMR Digital Output Module with a nominal voltage of 48 VDC. On-state voltage drop: With external termination, 10-foot cable < 4 VDC typical @ 500mA < 5 VDC maximum
