IS200HFPAG2ADC模拟量输入模块
一分钟冲击电压耐受：5 kV峰值，1.2/50µsec，0.5 J干扰试验耐受：SWC，根据ANSI C37.90.1和IEC 255-5振动测试耐受：IEC255-21-1环境环境温度范围：储存：-30°C至+70°C操作：-20°C至+55°C湿度：95%无冷凝输出触点数据跳闸输出（4个可编程继电器，每个触点2个）跳闸触点：连续额定值=3 A根据ANSI C37.9 0中断=60 VA电感，最大250 V或0.5 A报警输出（4个可编程继电器和5个预定义继电器，每个继电器1个触点）报警触点：持续额定值=3 A接通并携带5 A持续30秒中断=60 VA电感，最大250 V和0.5 A跳闸电流监测器灵敏度：150 mA跳闸电压监测器：38–300 VDC数字输入：38–30 VDC，1–3 mA通信接口数据系统接口：DB25，RS232端口–后面板DB9，RS232端口–前面板IRIG-B端口–后板（可选）打印机端口–后屏（可选）输入BURDENS电流电路：0.022Ω, I n=5 A 0.12时为5°Ω, 30°，I n=1 A@60 Hz 0.0507<4.738电压电路：0.30 VA，60 Hz 0.40 VA，50 Hz直流电池：电源：19 W，1个电源25 W，2个电源用于接触式转换器：额定电压下2.5 mA电源直流控制电压：48 VDC 38.5–60 VDC 110/125 VDC 88–150 VDC 220/250 VDC 176–300 VDC计量额定值标称频率：50或60 Hz频率跟踪：30–80 Hz标称电压（相位）：100–210 VAC额定电流：I n=1或5 A最大值允许电流：连续2 x I n三秒50 x I n一秒100 x I n最大允许交流电压：连续280 VAC一分钟（每小时一次）490 VAC精度RMS测量：±3%相角测量：±1°频率测量：±0.01 Hz定时器：设置的±3%数据时间标签分辨率：±1 ms保护输入=1 A输入=5 A通用差动（87G）：差动电流拾取：0.04–0.2 A 0.2–1.0 A%斜率系数：1–10 1–10电流不平衡（46A，46T）：负。顺序。电流拾取：0.01–0.60 A 0.5–2.99 A机器常数（46T）：1–45 1–45报警时间延迟（46A）：1-9秒1–9秒磁场损失（40）：1区和2区中心：12.5–300Ω 2.5 – 60 Ω 1区和2区A 0.5–16 A时间系数：0.1–99.99秒0.1–99.99秒DGP技术规范*技术规范如有更改，恕不另行通知。DGP数字发电机保护8 www.GEindustry.com/Multilin 3 DGP***DGP数字发生器保护1 1 A额定值5 5 A额定值0 1个电源，48 VDC 1 1个电源、110/125 VDC 2个电源、220/250 VDC 3两个电源、48 VDC 4个电源、110/125 VDC A带测试块，灰色外壳B无测试块，灰色案例A GE-MODEM通信协议B ModBus®通信协议（功能组A/B不可用）A功能组A参见DGP B功能组B选择指南*C右侧的功能组C A修订级别可选RS485到RS232转换器可用于ModBus®版本订购注意，需要具有特殊打印机端口配置的DGP继电器DEC1000才能正常工作。}*DGP选择指南功能组功能和特点A B C定子差动兼容--X通信端口2-RS232 2-RS232 2-RS232-DEC 1000A***00C DEC***从右侧的DEC选择指南†中选择三位数代码，或使用表1填写DEC1000输出继电器R1-R11的所需功能分配，并随订单一起提交。代码001至005已分配，可按说明使用。可以为DEC输出继电器分配F Vps=24–48 VDC H Vps=110–250 VDC选择配套DGP继电器中可用的任何保护功能。示例：DGP54BBCA–DGP额定值5 A，50/60 Hz，110/125 VDC冗余电源，无内置测试块，ModBus®协议，功能组C，版本A。以下特殊DGP™ 系统也可用。其他特殊情况请参考工厂
one min Impulse voltage withstand: 5 kV peak, 1.2/50 µsec, 0.5 J Interference test withstand: SWC, per ANSI C37.90.1 & IEC 255-5 Vibration test withstand: IEC255-21-1 ENVIRONMENTAL Ambient temperature range: Storage: -30° C to +70° C Operation: -20° C to +55° C Humidity: 95% without condensation OUTPUTS CONTACT DATA Trip outputs (4 programmable relays, 2 contacts each) Trip contacts: Continuous rating = 3 A Make and carry 30 A per ANSI C37.90 Interrupting = 60 VA inductive, maximum 250 V or 0.5 A Alarm outputs (4 programmable & 5 predefined relays, 1 contact each) Alarm contacts: Continuous rating = 3 A Make and carry 5 A for 30 sec Interrupting = 60 VA inductive, maximum 250 V or 0.5 A Trip current monitor sensitivity: 150 mA Trip voltage monitor: 38 – 300 VDC Digital inputs: 38 – 300 VDC, 1 – 3 mA COMMUNICATIONS INTERFACE DATA System interface: DB25, RS232 port – rear panel DB9, RS232 port – front panel IRIG-B port – rear panel (optional) Printer port – rear panel (optional) INPUTS BURDENS Current circuits: 0.022 Ω, 5° for I n = 5 A 0.12 Ω, 30° for I n = 1 A @ 60 Hz 0.0507 < 4.738 Voltage circuits: 0.30 VA, 60 Hz 0.40 VA, 50 Hz DC battery: Power supply: 19 W with 1 supply 25 W with 2 supplies For contact converters: 2.5 mA at rated voltage POWER SUPPLY DC control voltage: 48 VDC 38.5 – 60 VDC 110/125 VDC 88 – 150 VDC 220/250 VDC 176 – 300 VDC METERING RATINGS Nominal frequency: 50 or 60 Hz Frequency tracking: 30 – 80 Hz Nominal voltage (phase-phase): 100 – 210 VAC Rated current: I n = 1 or 5 A Maximum permissible current: Continuous 2 x I n Three sec 50 x I n One sec 100 x I n Maximum permissible AC voltage: Continuous 280 VAC One min (once per hour) 490 VAC ACCURACY RMS measurements: ± 3% Phase angle measurements: ± 1° Frequency measurements: ± 0.01 Hz Timers: ± 3% of setting Data time tag resolution: ± 1 ms PROTECTION In = 1 A In = 5 A General differential (87G): Differential current pickup: 0.04 – 0.2 A 0.2 – 1.0 A % slope factor: 1 – 10 1 – 10 Current unbalance (46A, 46T): Neg. seq. current pickup: 0.01 – 0.60 A 0.5 – 2.99 A Machine constant (46T): 1 – 45 1 – 45 Alarm time delay (46A): 1 – 9 sec 1 – 9 sec Loss of field (40): Zone 1 and Zone 2 center: 12.5 – 300 Ω 2.5 – 60 Ω Zone 1 and Zone .2 A 0.5 – 16 A Time factor: 0.1 – 99.99 sec 0.1 – 99.99 sec DGP Technical Specifications *Specifications subject to change without notice. DGP Digital Generator Protection 8 www.GEindustrial.com/Multilin 3 DGP * * * * * * DGP Digital Generator Protection 1 1 A rated 5 5 A rated 0 One power supply, 48 VDC 1 One power supply, 110/125 VDC 2 One power supply, 220/250 VDC 3 Two power supplies, 48 VDC 4 Two power supplies, 110/125 VDC A With test blocks, gray case B Without test blocks, gray case A GE-MODEM communication protocol B ModBus® communication protocol (not available with Function Group A/B) A Function Group A See DGP B Function Group B Selection Guide* C Function Group C on the right A Revision level Optional RS485 to RS232 converter available for use with ModBus® version Ordering Note that the DGP relay with special configuration of printer port is required for the DEC1000 to function properly. } *DGP Selection Guide FUNCTION GROUP FUNCTIONS AND FEATURES A B C Stator differential compatible — — X Communication ports 2-RS232 2-RS232 2-RS232 DEC 1000A *** * 00C DEC *** Select the three digit code from the DEC Selection Guide† on the right or fill in desired function assignment for the DEC1000 output relays R1-R11 using Table 1 and submit with the order. Codes 001 to 005 are already assigned and are available as described. Any protection function available in the companion DGP relay can be selected for the DEC output relay assignment F Vps = 24 – 48 VDC H Vps = 110 – 250 VDC Example: DGP54BBCA – DGP rated 5 A, 50/60 Hz, 110/125 VDC redundant power supplies, no built-in test blocks, ModBus® protocol, function group C, revision A. The following special DGP™ systems are also available. Refer to factory for other special
