IS200IGDMH1B电源模块,机器人模块
已安装O/S使用此功能选择要与系统一起使用的操作系统。重置配置数据如果要清除扩展系统配置数据，请选择是。默认值为“否”。启用缓存可提高处理器的速度。当CPU请求数据时，系统将所请求的数据从主DRAM传输到高速缓冲存储器中，在CPU处理之前，将其存储在高速缓冲存储器。默认设置为“启用”。6ohfw0hqx（qwhu6ohfw#6XE 0hqq）6DYHDQG([LW 106 C VMIVME-7750产品手册大磁盘访问模式大磁盘访问方式的选项是UNIX Novell Netware或其他。如果您正在安装新软件，但驱动器失败，请更改此选项，然后重试。不同的操作系统需要不同的驱动器几何图形表示。默认值为DOS。本地总线IDE适配器这将启用或禁用集成位置al总线IDE适配器。选项包括：禁用、主要、次要或两者。默认值为“两者”。高级芯片集控制选择高级芯片集控件将打开下面的菜单。使用此菜单更改芯片组寄存器中的值，以优化系统性能。视频引导类型选择“车载视频”以启用车载视频控制器作为引导显示设备。选择“禁用车载视频”以禁用车载视频控制器。视频格式选择为CRT、LCD或CRT_LCD。默认为CRT。3KRHQL默认主视频适配器选择“PCI”以使PCI视频卡（如果已安装）用于引导显示设备。不要选择“AGP”，因为VMIVME-7750不支持AGP。图形孔径选择AGP视频设备。选项包括：4MB、8MB、16MB、32MB、64MB、128MB或256MB。默认值为64MB。启用内存间隙如果已启用，请关闭系统RAM以释放地址空间，以便与选项卡一起使用。将在系统RAM中创建128KB的常规内存间隙（从512KB开始）或1MB的扩展内存间隙（以15MB开始）。选项为禁用、常规或扩展。默认设置为“禁用”。将中断分配给USB已启用将中断分配到USB。默认设置为“启用”。已启用传统USB支持支持USB上的传统键盘和鼠标。默认设置为“禁用”。卡总线内存大小启用时，允许从位于PCI到PCI桥后面的卡总线桥配置资源。默认设置为“禁用”。108 C VMIVME-7750产品手册安全使用此屏幕设置用户密码。启动时密码启用启动时的密码输入。默认设置为“禁用”。固定磁盘引导扇区写入保护硬盘上的引导扇区以防病毒。默认值为“正常”。软盘访问控制对软盘驱动器的访问。默认值为“用户”。病毒检查提醒在启动时显示提醒消息。选项是禁用的，每天、每周或每月。默认设置为“禁用”。系统备份提醒在启动时显示提醒消息。选项是禁用的，每天、每周或每月。默认设置为“禁用”。
Installed O/S Use this feature to select the operating system to use with your system. Reset Configuration Data Select Yes if you want to clear the extended system configuration data. The default is No. Cache Memory Enabling the cache memory enhances the speed of the processor. When the CPU requests data, the system transfers the requested data from the main DRAM into the cache memory where it is stored until processed by the CPU. The default is Enabled. 6HOHFW0HQX(QWHU6HOHFW#6XE0HQX)6DYHDQG([LW 3KRHQL[6HWXS8W 6HOHFW0HQX(QWHU6HOHFW#6XE0HQX)6DYHDQG([LW 106 C VMIVME-7750 Product Manual Large Disk Access Mode The options for the Large Disk Access Mode are UNIX Novell Netware or Other. If you are installing new software and the drive fails, change this selection and try again. Different operating systems require different representations of drive geometries. The default is DOS. Local Bus IDE Adapter This enables or disables the intergrated local bus IDE adapter. The options are: Disabled, Primary, Secondary or Both. The default is Both. Advanced Chipset Control Selecting Advanced Chipset Control opens the menu below. Use this menu to change the values in the chipset register for optimizing your system’s performance. Video Boot Type Select “Onboard Video’ to enable the onboard video controller as the boot display device. Select “Disable Onboard Video’ to disable the onboard video controller. Video Format Selections are CRT, LCD or CRT_LCD. The default is CRT. 3KRHQL Default Primary Video Adapter Select ‘PCI’ to have a PCI video card, if installed, used for the boot display device. Do not select ‘AGP’ as the VMIVME-7750 does not support AGP. Graphics Aperture Select the size of the graphics aperture for the AGP video device. The options are: 4MB, 8MB, 16MB, 32MB, 64MB, 128MB or 256MB. The default is 64MB. Enable Memory Gap If enabled, turn system RAM off to free address space for use with an option card. Either a 128KB conventional memory gap, starting at 512KB, or a 1MB extended memory gap, starting at 15MB, will be created in the system RAM. The options are Disabled, Conventional or Extended. The default is Disabled. Assign Interrupt To USB Enabled assigns an interrupt to the USB. The default is Enabled. Legacy USB Support Enabled supports a legacy keyboard and mouse on the USB. The default is Disabled. Card Bus Memory Size When enabled, allows resources to be configured from a Card Bus Bridge located behind a PCI-to-PCI Bridge. The default is Disabled. 108 C VMIVME-7750 Product Manual Security Utilize this screen to set a user password. Password On Boot Enables password entry on boot. The default is Disabled. Fixed Disk Boot Sector Write protects boot sector on the hard disk to protect against viruses. The default is Normal. Diskette Access Controls access to the diskette drives. The default is User. Virus Check Reminder Displays reminder message at bootup. The choices are disabled, daily, weekly or monthly. The default is Disabled. System Backup Reminder Displays reminder message at bootup. The choices are disabled, daily, weekly or monthly. The default is Disabled.
