IS200TBAIH1B处理器模块,备件模块
用于带状电缆的三个34针IDC连接器尺寸：端子板219mm长X 95mm宽X 30mm深尺寸：接口模块145mm长X 109mm宽X 101mm深（包括配套连接器，包括安装支架）外部输入GMR模式：15/16常闭开关，串联齐纳二极管，用于三态输入（15个带自动测试）。非GMR模式：15/16常开开关，三态输入并联齐纳二极管（15带自动测试）。打开开关电压双态或三态GMR模式：电源电压。三态非GMR模式：齐纳电压闭合开关电流双态：24V供电时为11mA。三态，GMR模式：24V电源下7mS。三态、非GMR模式：24V电源下11mA Silvertech零件号GBC1-SC-DI16 GBC1-SK-DI16 IMC3-SC-DO16 IMC3-STC-DO16 CBL1 CK RRnn CBL1 CK EEnn CBL1 CK-ENN端子板16电路源块组16电路汇块接口模块端子板。16路接收模块组的接口模块。34路带状电缆，终端板至接口模块现场设备连接电缆，带2个ELCO 8016连接器现场设备连接线缆，带1个ELCO 801 6连接器，另一端带剥线和镀锡连接器。32点离散输入接线板和接口模块的规范工作电压16V至30V DC温度范围0至+60℃湿度5%至95%非冷凝连接器：接口模块两个32点ELCO公8016系列，38针外露触点。用于带状电缆的三个34针IDC连接器尺寸：端子板219mm长X 110mm宽X 30mm深尺寸：接口模块145mm长X 109mm宽X 101mm深（包括配套连接器，包括安装支架）外部输入32个带短路保护的开关输入31具有自动测试断开开关电压电源电压–1V闭合开关电流每点7mA天才街区。24V时最大21mA，3块。Silvertech零件号GBC1-SC-DI32 GBC1-SK-DI32 IMC3-SC-DI32IMC3-SK-DI32CBL1 CK RRnn CBL1 CK EEnn CBL1 CKEBnn 32电路源块用端子板32电路汇块接口模块32电路源模块组用端子板。32路汇模块组的接口模块。34路带状电缆，终端板至接口模块现场设备连接电缆，带2个ELCO 8016连接器现场设备连接线缆，带1个ELCO 801 6连接器，另一端带剥线和镀锡连接器。GFT-177A第4节产品规范4-29 4模拟输入端接板和接口模块模拟输入端接线板可用于6点电流输入Genius块。一个互补的模拟输入接口模块可与一个用于接线的极化锁定两部分连接器一起使用。模拟输入接口模块通过精密电阻器将输入电流转换为电压信号，以分配给终端板。电阻器完全受到保护，不受电源线短路的影响。终端板为由点电源供电的每个点配备了高输入阻抗电压-电流转换器。模拟输入终端板和接口模块规范工作电压18V至56V DC温度范围0至+60摄氏度湿度5%至95%非冷凝连接器：接口模块一个ELCO公8016系列，38针外露触点。
Three 34-pin IDC connectors for ribbon cable Size: Termination Boards 219mm length X 95mm width X 30mm depth Size: Interface Modules 145mm length X 109 mm width X 101mm depth (including mating connector, including mounting bracket) External Inputs GMR Mode: 15/16 normally closed switches with zener diodes in series for tristate inputs (15 with autotest). Non-GMR Mode: 15/16 normally open switches with zener diodes in parallel for tristate inputs (15 with autotest). Open Switch Voltage Bistate or tristate GMR Mode: supply voltage . Tristate non-GMR Mode: zener voltage Closed Switch Current Bistate: 11mA at 24V supply . Tristate, GMR Mode: 7mS at 24V supply. Tristate, nonGMR Mode: 11mA at 24V supply Silvertech part numbers GBC1-SC-DI16 GBC1-SK-DI16 IMC3-SC-DO16 IMC3-SK-DO16 CBL1-CK-RRnn CBL1-CK-EEnn CBL1-CK-EBnn Termination Board for 16-circuit Source block Termination Board for 16-circuit Sink block Interface Module for 16-circuit Source block group. Interface Module for 16-circuit Sink block group. 34-way ribbon cable, termination board to interface module Field device connection cable with 2 ELCO 8016 connectors Field device connection cable with 1 ELCO 8016 connector and stripped and tinned connectors at the other end. Specifications for 32–Point Discrete Input Termination Boards and Interface Modules Operating voltage 16V to 30V DC Temperature range 0 to +60 degrees C Humidity 5% to 95% non-condensing Connectors: Interface Module Two 32-point ELCO male 8016 series, 38-pin exposed contacts. Three 34-pin IDC connectors for ribbon cable Size: Termination Boards 219mm length X 110 mm width X 30mm depth Size: Interface Modules 145mm length X 109 mm width X 101mm depth (including mating connector, including mounting bracket) External Inputs 32 switched inputs with Short Circuit protection31 with autotest Open Switch voltage Supply voltage – 1V Closed Switch current 7mA per point per Genius Block. 21mA max. with 3 blocks at 24V. Silvertech part numbers GBC1-SC-DI32 GBC1-SK-DI32 IMC3-SC-DI32 IMC3-SK-DI32 CBL1-CK-RRnn CBL1-CK-EEnn CBL1-CK-EBnn Termination Board for 32-circuit Source block Termination Board for 32-circuit Sink block Interface Module for 32-circuit Source block group. Interface Module for 32-circuit Sink block group. 34-way ribbon cable, termination board to interface module Field device connection cable with 2 ELCO 8016 connectors Field device connection cable with 1 ELCO 8016 connector and stripped and tinned connectors at the other end. GFT-177A Section 4 Product Specifications 4-29 4 Analog Input Termination Boards and Interface Modules An analog input termination boards is available for the 6-point current input Genius block. A complementary analog input interface module is available with a polarized locking two-part connector for wiring. The analog input interface module converts the input current into a voltage signal via a precision resistor for distribution to the termination boards. The resistor is fully protected from short circuits in the power wiring. The termination board incorporates a high input impedance voltage-to-current converter for each point which is powered by the point power supply. Specifications for Analog Input Termination Boards and Interface Modules Operating voltage 18V to 56V DC Temperature range 0 to +60 degrees C Humidity 5% to 95% non-condensing Connectors: Interface Module One ELCO male 8016 series, 38-pin exposed contacts.
