IS200TREGH1A工业自动化卡件
如果模块处于冻结模式，手持式编程器将在屏幕上返回CFG ERR信息，如下所示：R0:03*CFG ERR 30m Versax：所有电源、I/O和通信模块绝缘绝缘耐受UL508、UL840、IEC664 1.5KV，适用于额定值为51v至250v的模块电源输入电压骤降、电压骤降EN 61000-4-11*运行期间：电压骤降至30%和100%，交流电压骤降至10%，DC 20%*EN 61000-4-x系列试验的等级在技术上等同于IEC 1000-4-x和IEC 801-x系列。注1：GE Fanuc网站：GEfanuc.com/support/plc上列出了模块特定许可。访问该页面后，下载文件Agenty.zip，然后提取包含数据的.xls电子表格。注2：参考模块特定数据表和安装C部分1级figure_ap 1级表_ap 1层GFK-0898F C-1附录C I/O电缆数据表本附录提供了描述I/O系统中可使用的每种90-30系列电缆类型的数据表。这些数据表中的信息适用于由Series 90-30 PLC或安装有Persol计算机接口卡的PC控制的I/O系统。本附录包含以下数据表：IC693CBL300/301/302/312/313/314–I/O总线扩展电缆IC693CBL 306/307–高密度I/O模块的扩展电缆（50针）（24针）用于高密度I/O模块IC693CBL321/322/323–用于高密度输入/输出模块的过时输入/输出电缆（24针IC693CBL300/301/302/312/313/314 I/O总线扩展电缆（包括构建定制长度电缆的说明）描述I/O总线扩展线缆（IC693CBL 300301312313314），称为“Y形电缆”，一端有一个单le 25针D连接器，另一端有两个双头（一le，一fele）25针D接头，如图（a）所示。50英尺（15m）（IC693CBL302）电缆在底板端有一个单端电缆连接器，在扩展底板端有单端电缆电缆连接器。3英尺电缆（IC693CBL300）也可用作WYE适配器电缆，以简化构建自定义长度电缆（请参阅本章后面的“电缆应用建议”一节）。a43853.5、3、6、26英尺电缆50英尺电缆毡连接器LE连接器LE连接器E连接器LE连接器A B图B-1。I/O总线扩展电缆详细信息电缆长度IC693CBL300 3英尺（1米），连续屏蔽IC693CBL 301 6英尺（2米），持续屏蔽IC693C BL302或IC693C BL 314 50英尺（15米），电缆的连续屏蔽功能I/O总线扩展电缆用于在需要额外的I/O插槽或基板与基板有一定距离时，将I/O总线扩展到Series 90-30 I/O系统中的扩展或远程基板。pred I/O总线扩展电缆可用于连接扩展或远程底板。如果标准电缆无法提供所需的电缆长度，则必须构建自定义电缆（详细说明请参阅“构建自定义长度I/O总线扩展电缆”一节）。输入/输出电缆数据表C GFK-0898F附录C–输入/输出数据表C-3连接电缆将单个电缆连接器连接至基板右侧的25针毛毡连接器。将电缆双连接器端的le连接器连接到第一个扩展底板上的25针fele连接器。将电缆双连接器端上未使用的25针fele连接器连接到第二条I/O总线扩展电缆的单le连接器以继续I/O总线扩展链，或者连接到I/O总线端子插头（如果这是扩展链中的最后一条电缆）。关于I/O总线扩展电缆的重要说明1。
If the module is in freeze mode, the Hand-Held Programmer will return with a CFG ERR message on the screen as follows: R0:03*CFG ERR 30m Versax: All power supply, I/O, and communication modules ISOLATION Dielectric Withstand UL508, UL840, IEC664 1.5KV for modules rated from 51v to 250v POWER SUPPLY Input Dips, riations EN 61000-4-11* During Operation: Dips to 30% and 100%, riation for AC 10%, riation for DC 20% * EN 61000-4-x series of tests are technically equilent to the IEC 1000-4-x and IEC 801-x series. te 1: Module specific approls are listed on the GE Fanuc web site: GEfanuc.com/support/plc. After accessing that page, download the file Agency.zip, then extract the .xls spreadsheet containing the data. te 2: Refer to module specific data sheets & installat C section level 1 figure_ap level 1 table_ap level 1 GFK-0898F C-1 Appendix C I/O Cable Data Sheets This appendix provides data sheets describing each of the Series 90-30 cable types that can be used in an I/O system. The infortion in these data sheets applies to I/O systems controlled by either a Series 90-30 PLC or by a PC with an installed Persol Computer Interface card. This appendix contains the following data sheets: IC693CBL300/301/302/312/313/314 – I/O Bus Expansion cables IC693CBL306/307 – Extension cables (50-pin) for high-density I/O modules IC693CBL308/309 – I/O Interface cable (50-pin) for high-density I/O modules IC693CBL310 – OBSOLETE I/O Interface cable (24–pin) for high density I/O modules IC693CBL315 – OBSOLETE I/O Interface cable (24-pin) for high-density I/O modules IC693CBL321/322/323 – OBSOLETE I/O cables (24–pin) for high–density I/O modules IC693CBL327/328 – I/O Interface cables (24–pin) for high–density I/O modules IC693CBL329/330/331/332/333/334 – I/O Interface cables (24–pin) for high–density I/O modules C C-2 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F IC693CBL300/301/302/312/313/314 I/O Bus Expansion Cables (Includes Instructions for Building Custom Length Cables) Description I/O bus expansion cables (IC693CBL300, 301, 312, 313, 314), called “Wye cables,” have a single le 25-pin D connector on one end and a two-headed (one le, one fele) 25-pin D connector on the other end as shown in (A) of the figure. The 50 foot (15m) (IC693CBL302) cable has a single le connector on the baseplate end and a single termited le connector on the expansion baseplate end. The 3 foot cable (IC693CBL300) can also be used as a WYE adapter cable to simplify building custom length cables (see the section “Cable Application Suggestions” later in this Chapter). a43853 .5, 3, 6, 26 FOOT CABLES 50 FOOT CABLE FELE CONNECTOR LE CONNECTOR LE CONNECTOR LE CONNECTOR LE CONNECTOR A B Figure B-1. Detail of I/O Bus Expansion Cables Cable Lengths IC693CBL300 3 feet (1 meter), continuous shield IC693CBL301 6 feet (2 meters), continuous shield IC693CBL302 or IC693CBL314 50 feet (15 meters), continuous shield IC693CBL312 0.5 feet (0.15 meters), continuous shield IC693CBL313 25 feet (8 meters), continuous shield Function of Cables The I/O Bus expansion cables are used to extend the I/O bus to expansion or remote baseplates in a Series 90-30 I/O system when additiol I/O slots are needed or baseplates are required some distance from the baseplate. The pred I/O bus expansion cables can be used for connecting either expansion or remote baseplates. Where required cable length is t ailable in a standard cable, a custom cable must be built (see the section “Building Custom Length I/O Bus Expansion Cables” for detailed instructions). I/O Cable Data Sheets C GFK-0898F Appendix C – I/O Cable Data Sheets C-3 Connecting the Cables Connect the single le connector to the 25-pin fele connector on the right side of the baseplate. Connect the le connector on the dual connector end of the cable to the 25-pin fele connector on the first expansion baseplate. Connect the unused 25-pin fele connector on the dual connector end of the cable to either the single le connector of a second I/O bus expansion cable to continue the I/O bus expansion chain, or to an I/O bus Termitor plug if this is the last cable in the expansion chain. Important tes About I/O Bus Expansion Cables 1.
