IS200VVIBH1B控制模块,机器人模块
如果使用抑制，负载将接近电阻负载接触寿命。下图为交流和直流负载的典型抑制。直流负载典型抑制中所示的A V二极管是行业标准N。交流负载抑制所示的电阻和电容是大多数电子分配器的标准部件。直流负载继电器直流电源A V aA负载线圈现场接线信息下图提供了连接用户提供的输入和负载设备以及电压输入继电器电源的接线信息。继电器~交流电源。aA AC负载V W负载线圈Ω 规范F B S现场布线a a a a B a a a T用于其他光学耦合器其他继电器 为输入点提供一个单电源输入，并在其中打开继电器。输入被设计为具有正或负的不对称性，因为它们从用户mon的输入设备吸收或提供电流，并且被布置为一组输入。继电器分为两组，每组四个。每个小组都有一种魔力。输入整流器适用于各种用户提供的设备，例如：推压限位开关和电子接近开关。通过输入的电流导致输入状态选项卡I中的逻辑。现场设备的电源必须由用户提供。rllyopen继电器用于控制用户提供的负载。ea的swing容量为。继电器可以控制各种用户提供的负载设备，如：多个星形信号和标记。内部继电器的电源由背板上的+伏直流总线提供。用户必须为现场设备提供交流或直流电源。这上面有保险丝。提供每个点关闭状态的D标记位于。D布置在两个水平行中，每行中有八个绿色D。p行通过输入点标记为A，底部行通过中继点标记为B。铰链门的内外表面之间有一个插件。当铰链门关闭时，其内侧的表面上有接线信息，外部表面上可以记录识别信息。插入件外ft边缘的p半部分是彩色编码的蓝色低电压s，外ft边缘底部的半部分是红色高电压s。这可以安装在系统的任何插槽或插槽中。规格F表。ICMDR输入规范Rad电压伏特DC输入电压范围+伏特DC输入每一组八个输入之间的隔离电压RMS和输入之间的逻辑侧电压RMS输入电流。
If suppression is used, the load will approach the resistive load contact life. The following figure shows typical suppression of AC and DC loads. The A V diodes shown in the typical suppression of DC loads are industry standard N. The resistance and capacitance shown for AC load rejection are standard components of most electronic distributors. Field wiring information of DC power supply A V aA load coil of DC load relay The following figure provides the wiring information for connecting user provided input and load equipment and voltage input relay power supply. Relay~AC power supply. AA AC load V W load coil Ω specification F B S field wiring a a a a B a a T for other optical couplers Other relays provide a single power input to the input point and open the relay therein. The inputs are designed to have a positive or negative asymmetry because they absorb or supply current from the user mon's input device and are arranged as a set of inputs. The relay is divided into two groups of four. Each group has a magic power. Input rectifiers are suitable for various user supplied devices, such as push limit switches and electronic proximity switches. The current through the input causes the logic in the Input Status tab I. The power supply of field equipment must be provided by the user. The rllyopen relay is used to control the load provided by the user. The swing capacity of ea is. Relays can control various user supplied load devices, such as multiple star signals and markers. Power for the internal relays is provided by the+V DC bus on the backplane. The user must provide AC or DC power for the field equipment. There is a fuse on this. The D marker that provides the closing status of each point is located at. D is arranged in two horizontal rows with eight green Ds in each row. The p line is marked as A through the input point, and the bottom line is marked as B through the relay point. There is a plug-in between the inner and outer surfaces of the hinged door. When the hinged door is closed, there is wiring information on the inner surface and identification information can be recorded on the outer surface. The p half of the outer ft edge of the insert is a color coded blue low voltage s, and the red high voltage s is the bottom half of the outer ft edge. This can be installed in any slot or slot in the system. Specification F table. ICMDR input specification Rad voltage Volt DC input voltage range+Volt DC input Isolation voltage RMS between each group of eight inputs and logic side voltage RMS input current between inputs.
