IS200VVIBH1C/IS200VVIBH1C工业卡件,ABB卡件
铰链门的内外表面之间有一个插件。当铰链门关闭时，其内侧的表面上有接线信息，外部表面上可以记录识别信息。插入件的外边缘为蓝色，表示低电压。这可以安装在系统的任何插槽或插槽中。表。Rad Voltage volts DC Input Voltage Range+volts DC Inputs per one group with singmon Isolation volts between field side and logic side Input Current at Rad Voltage Input aracritics Onsta Voltage（射频电压直流输入电压范围+每组直流输入电压）规范，励磁侧和逻辑侧输入电流在射频电压下典型。伏特直流偏置电压+伏特直流启动电流。最小偏置电流。打开响应时间ms典型关闭响应时间ms一般功耗：V底板上电压总线上的所有输入功耗：V Isolad电压底板总线或用户提供的电源有关产品标准和一般规范，请参阅附录B。规范F输入现场接线信息下图提供了连接用户提供的输入设备和电源的接线信息，以及电压直流正负逻辑输入。S现场布线a a a a B B B B a a a a a B B a B B其他S N C V OUT OV OUT。K光学耦合器。fµ图。现场接线电压DC正负逻辑输入C C C环境温度C a V电源C C图上的输入数量。本数据表的输入点与温度是针对Volt AC输入点的，网址：www.cimcaution.partsp.aspx r提供了该GE的接线图和安装指南。有关更多信息，请联系supportqualirol的Qualrol支持。差分输入F apr差分输入V AC输入点逻辑控制器的V AC输入为输入点提供单电源输入。输入为无功电阻电容输入。输入点中的电流导致输入状态选项卡I中的逻辑。输入异常与用户提供的各种输入设备相关联，如推压限制开关和电子接近开关。现场设备的电源必须由用户提供。这需要交流电源，但不能与直流电源一起使用。提供每个点关闭状态的D标记位于。该D块有两个水平行，每行有八个绿色D；p行标记为A通过点通过，底部行标记为B通过点通过。铰链门的内外表面之间有一个插件。当铰链门关闭时，其内侧的表面上有接线信息，外部表面上可以记录识别信息。插入件的外边缘为红色，表示高压。这可以安装在系统的任何插槽或插槽中。表。射频电压伏特交流输入电压范围伏特交流Hz每一组输入电压，励磁侧和逻辑侧之间的隔离电压RMS，射频电压输入时的典型输入电流：起始电压伏特交流偏置电压伏特交流起始电流最小偏置电流。打开响应时间ms关闭响应时间ms背板上的电压总线上的所有输入的消耗输入的数量取决于环境温度，如图所示。产品标准和一般规范参见附录B。规范F输入现场接线信息下图提供了连接用户提供的输入设备和电源的接线信息
An insert goes between the inside and outside surface of the hinged door. The surface wards the inside of the when the hinged door is closed has wiring infortion and identification infortion can be recorded on the outside surface. The outside ft edge of the insert is colorcoded blue indica a lowvoltage . This can be instald in any slot of a or slot in a sysm. Tab . Specifications for Rad Voltage volts DC Input Voltage Range + volts DC Inputs per one group with a sing mon Isolation volts between field side and logic side Input Current typical at rad voltage Input aracristics Onsta Voltage . volts DC Offsta Voltage + volts DC Onsta Current . minimum Offsta Current . On response Time ms typical Off response Time ms typical Power Consumption: V all inputs on from volt bus on backplane Power Consumption: V from the Isolad volt backplane bus or from user supplied power Refer Appendix B for product standards and general specifications. Specifications F Input Field Wiring Infortion The following figure provides wiring infortion for connecting user supplied input devices and power source the volt DC positivenegative logic input . S FIELD WIRING a A A A A A A A A B B B B B B B B RY OTHER S N C V OUT OV OUT .K OPTICAL COUPR . f µ Figure . Field Wiring Volt DC PositiveNegative Logic Input C C C C NUMBER OF INPUTS ON AMBIENT MPERATURE C a V SUPPLY C C Figure . Input Points vs. mperature for This Datasheet is for the Volt AC Input Point http:www.cimcaution.partsp.aspx rProvides the wiring diagrams and installation guidelines for this GE . For further infortion pase contact Qualitrol Support at supportqualitrol. Discre Input s F apr Discre Input s Volt AC Input Point The volt AC Input for the Logic Controlr provides input points with one mon power input . The input s are reactive resisrcapacir inputs. Current in an input point results in a logic in the input status tab I. Input aracristics are patib with a wide range of usersupplied input devices su as pushbutns limit swis and ectronic proximity swis. Power opera the field devices must be supplied by the user. This requires an AC power source it cant be used with a DC power source. D indicars whi provide the OFF status of ea point are locad at the p of the . This D block has two horizontal rows with eight green Ds in ea row; the p row labed A through points through and the botm row labed B through points through . An insert goes between the inside and outside surface of the hinged door. The surface wards the inside of the when the hinged door is closed has wiring infortion and identification infortion can be recorded on the outside surface. The outside ft edge of the insert is colorcoded red indica a highvoltage . This can be instald in any slot of a or slot in a sysm. Tab . Specifications for Rad Voltage volts AC Input Voltage Range volts AC Hz Inputs per one group with a sing mon Isolation volts RMS between field side and logic side Input Current typical at rad voltage Input aracristics: Onsta Voltage volts AC Offsta Voltage volts AC Onsta Current minimum Offsta Current . On response Time ms Off response Time ms Consumption all inputs on from volt bus on backplane Number of inputs on is dependent upon ambient mperature as shown in figure . Refer Appendix B for product standards and general specifications. Specifications F Input Field Wiring Infortion The following figure provides wiring infortion for connecting user supplied input devices and power source
