IS210AEAAH3BKE处理器卡件
只有当它们有东西传输时才打开它们。和CMM的情况就是如此。然而，在px多点配置中，必须对Isolad-ReparConverter的上游变送器进行特殊sps。旋转上游变送器。对于在Isolad-ReparConverter的J端口激活的RS驱动器，J处的RTS输入必须为真。RS驱动器在J端口的状态取决于装置上开关的位置。当开关处于中心位置C安装和硬件八月Q C模拟多点配置此配置显示了如何使用Isolad RepearConverter连接信号转换或grear距离。 转换器的系统配置Q附录C ICCCM ISOLAD repearConverter C Rus用于在px网络中使用RepearConvertrpx多点网络，包括s和RS reparconvers砖块，适用以下规则：Ru：使用砖块作为repar时，端口J应始终朝向主机设备，端口J应该始终远离主机设备。砖块侧面的开关位置应始终处于中央位置on。端口J直接朝向主机的唯一情况是砖块用作从站的转换器RS。开关处于正确位置CTS。Ru：如果CMM从设备位于砖组的下游，则CMM串行端口NE流量控制的配置与ms调制解调器旋转延迟仅应用CCM SNP和SNPX程序。Ru：在主机和从设备之间的通信路径中，不要放置超过三块砖。C安装和硬件八月Q C驾驶室图下图中的驾驶室图被称为前面图中系统配置的驾驶室AE。这些图表显示了构建自己的驾驶室的原理，可以根据您的具体应用进行修改。 转换器 在三坐标测量机上的驾驶室丘内。如图所示，当通过以主方式配置驾驶室来减少传输线路上的多点布线时，不能沿着传输长度使用条带或其他类型的电缆，如SR CMM从属内置端口CMM从属引脚FE CMM端口或DS屏蔽内多点KE连接上的其他设备S引脚 仅在第一次和最后一次跌落时使用RMI连接：在CMM上安装跳线连接
Only open them when they have something to transfer. This is the case with CMM. However, in a px multipoint configuration, a special sps must be performed on the upstream transmitter of the Isolad ReparConverter. Rotate the upstream transmitter. For RS drives activated at port J of Isolad ReparConverter, RTS input at J must be true. The status of RS driver at port J depends on the position of the switch on the device. When the switch is installed in the central position C and the hardware is in the August Q C analog multipoint configuration, this configuration shows how to use the Isolate RepearConverter to connect signal conversion or grear distance. The system configuration of the converter Q Appendix C ICCCM ISOLAD researConverter C Rus is used to use the RepearConvertrpx multipoint network in the px network, including the s and RS reparconvers bricks. The following rules apply: Ru: When using bricks as repars, port J should always face the host device, and port J should always be away from the host device. The switch position on the side of the brick should always be in the central position on. The only case where the port J is directly facing the host is when the brick is used as the converter RS of the slave station. The switch is in the correct position CTS. Ru: If the CMM slave device is located downstream of the brick group, the configuration of the CMM serial port NE flow control and the ms modem rotation delay only apply the CCM SNP and SNPX programs. Ru: Do not place more than three bricks in the communication path between the host and the slave. C installation and hardware August Q C cab diagram The cab diagram in the following figure is called the cab AE of the system configuration in the previous figure. These diagrams show the principle of building your own cab, which can be modified according to your specific application. The converter is located in the cab of the CMM. As shown in the figure, when the cab is configured in the master mode to reduce the multi-point wiring on the transmission line, it is not allowed to use strips or other types of cables along the transmission length, such as SR CMM slave built-in port CMM slave pin FE CMM port or other devices on the multi-point KE connection in the DS shield S pin only uses RMI connection during the first and last drop: install jumper connection on the CMM
