IS215VCMHIH2B工控备件机器人模块
否则可能造成人身伤害或死亡、财产损失或破坏，或两者兼而有之。颜色代码这些颜色代码通常用于Unid Stas制造的工业设备。他们在这里作为参考。如果它们与适用于您所在地区或设备类型的代码冲突，则应遵循适用代码insad。除了满足代码要求外，彩色编码还可以更安全、更容易。绿色或绿色，带条纹接地黑色Priry AC红色次要AC蓝色DC白色或中性黄色次要电源不受输入断开控制。艺术指导人员，即使设备与内部电源断开，也可能存在外部电源供电。布线减少了彼此之间的噪声耦合。请记住，您应将电气噪声布线（如交流电源布线）和离散布线（如直流和模拟输入布线或驾驶室）与低电平信号布线（如电缆）物理隔离。这可以通过在可行的情况下对以下接线类别进行单独分组来实现：交流电源接线。这包括电源的交流输入以及控制柜中的其他交流设备。模拟输入或接线。这应该被屏蔽，以进一步减少噪声耦合。有关详细信息，请参阅规范。布线不规范。这些N型感应负载在关闭时会产生噪音尖峰。直流输入接线。尽管这些低电平输入在本质上受到抑制，但应通过观察这些布线实践进一步防止噪声耦合。驾驶室。接线如Genius总线或串行驾驶室应远离产生噪音的接线。安装和硬件八月Q当交流或接线束必须通过噪声敏感信号接线束附近时，避免它们并排运行。将它们弯曲，这样，如果它们交叉，它们就会在直角方向交叉。这将使它们之间的耦合最小化。分组保持分段如果实际的话，机架中类似的分组可以帮助保持布线分段。例如，一个机架可以只包含AC，而另一个机架只能包含DC，每个机架还可以按输入和类型进一步分组。以slr系统为例，机架的左端可能包含模拟信号，中间可能包含直流信号，右端可能包含交流信号。不同的连接方法对于带有点或ss的系统，标准方法是使用带有这些信号的电路板。该板可方便地对用户提供的输入和设备进行现场布线，并在现场更换，而不会干扰现有的现场布线。一些离散点可用于可选的块快速连接TBQC组件。此组件包含一个替换板的内置面板。该组件还包含一个DINrail墩块和一个连接墩块的驾驶室。这种方法的优点是，与从用户提供的面板块或条上手工布线相比，它节省了大约两个小时的布线时间。旧点的前端有一个销，该销要么由一端带有Weidmull面板块Weidmullr目录号的驾驶室连接，要么由带有用户提供的剥开的镀锡广告的驾驶室或带连接。
Failure do so can ad personal injury or death property dage or destruction or both. Color Coding s These color codes are monly used in industrial equipment nufactured in the Unid Stas. They are cid here as a reference. Where they are in conflict with codes that apply your area or your type of equipment you should follow your applicab codes insad. Besides satisfying code requirements color coding kes sting and troubshooting safer fasr and easier. Green or green with stripe Ground Black Priry AC Red Secondary AC Blue DC Whi mon or neutral Yellow Secondary power source not controld by the in disconnect. Arts innance personnel that there y be power present from an exrnal source even if the equipment is disconnecd from its in power source. Routing reduce noise coupling among s it is remended you keep ectrically noisy wiring su as AC power wiring and Discre wiring physically separad from lowvel signal wiring su as DC and Analog Input wiring or cabs. This can be acplished by grouping separaly where practical the following cagories of wiring: AC power wiring. This includes the AC input the power supply as well as other AC devices in the control cabinet. Analog Input or wiring. This should be shielded further reduce noise coupling. See the Specifications for details. Discre wiring. These ofn swit inductive loads that produce noise spikes when swid off. DC Input wiring. Although suppressed inrnally these lowvel inputs should be further procd against noise coupling by observing these wiring practices. Cabs. Wiring su as Genius Bus or serial cabs should be kept away from noiseproducing wiring. Installation and Hardware August Q Where AC or wiring bunds must pass near noisesensitive signal wiring bunds avoid running them beside ea other. Rou them so that if they have cross they do so at a right ang. This will minimize coupling between them. Grouping s Keep s Segregad If practical grouping similar s gether in the racks can help keep wiring segregad. For examp one rack could contain only AC s and a different rack only DC s with further grouping in ea rack by input and types. For slr sysms as an examp the ft end of a rack could contain Analog s the midd could contain DC s and the right end could contain AC s. Discre Connection Methods For s with points or ss the standard method is use the board whi es with these s. The board kes it easy pre field wiring the user supplied input and devices and replace s in the field without disturbing existing field wiring. Some discre point s can be used with an optional Block Quick Connect TBQC assembly. This assembly contains a facepla with builtin that replaces the board. The assembly also contains a DINrail mound block and a cab connect the the block. The advantage of this method is that it saves about two hours of wiring time per pared with hand wiring from a ’s board a usersupplied panelmound block or strip. Older point s have one pin on the front of the that is either connecd by a cab with a on ea end a Weidmulr panelmound block Weidmulr catalog no. or is connecd by a cab with stripped tinned ads a usersupplied block or strip.
