IS220PDOAH1B工业自动化卡件
电路触点块类别。800T单电路接触块类别。800T号正常电路操作接线符号OUT Position IN Position CENTER Position自我监控块仅用于2位装置。仅在级别1上可用。当正确熔断至IEC 269-1和269-2时，具有常闭触点的接触块符合直接驱动正开标准要求。浅触点/微型触点：10 A gl或N型盒式保险丝。PenTUFF触点：6 A gl或N型盒式保险丝。800T和800H按钮用800T和800 H照明设备接触块的可用配件接触目标表缩写和符号NO=常开NC=常闭EM=早开LB=晚间休息O=打开X=关闭图5图4 40061-052-01 DIR 40061-052（版本11）版权所有©2013，股份有限公司保留所有权利。罗克韦尔软件在美国印刷，是股份有限公司的商标。商标不属于其各自公司的财产。出版物警告：只能在I级2类危险场所的设备上使用密封开关和逻辑簧片块。更换接触块可能会影响2类的适用性。接触某些化学品可能会降低密封接触块中使用的材料的密封性能。常开（NO）触点、密封开关触点块和逻辑簧片触点块不能用于紧急停机控制电路。警告：800T-N296不适用于I级2类危险场所。5 5 5 3 3 3 1 2 3 SIP-WS 800P www.commend.com安全和通信产品的设计和/或规格可能会因改进而发生更改，恕不另行通知。错误除外。SIP-WS 800P数据表V1.0/0416 SA|1带LCD图形显示器的耐SIP壁装式站具有OpenDuplex®功能的SIP站SIP-WS 800 P已开发并设计用于安全要求较高的区域。该站直接与以太网（LAN/WAN）连接，并以此方式通过IP网络连接到兼容的SIP服务器。具有下行链路功能的内置交换机允许直接连接其他IP设备（例如IP摄像机）。除了高容量外，SIP站还提供了大量
Circuit Contact Block Cat. No. 800TSingle Circuit Contact Block Cat. No. 800TNormal Circuit Operation Wiring Symbol OUT Position IN Position CENTER Position Self Monitoring Block to be used only on 2 position devices. Only functional on level 1. Contact blocks with normally closed contacts meet direct drive positive opening standard requirements when properly fused to IEC 269-1 and 269-2. Shallow/mini contacts: 10 A gl or N type cartridge fuse. PenTUFF contacts: 6 A gl or N type cartridge fuse. Available Accessories for 800T and 800H Illuminated Device Contact Blocks for 800T and 800H Push Buttons Contact Target Table Abbreviations and Symbols NO = Normally Open NC = Normally Closed EM = Early Make LB = Late Break O = Open X = Closed Fig. 5 Fig. 4 40061-052-01 DIR 40061-052 (Version 11) Copyright © 2013 , Inc. All Rights Reserved. Printed in USA. , Rockwell Software, and are trademarks of , Inc. Trademarks not belonging to are property of their respective companies. Publication WARNING: OnlySealed Switch and Logic Reed Blocks may be used on devices rated for Class I, Division 2 Hazardous Locations. Substitution of the contact block may impair suitability for Division 2. Exposure to some chemicals may degrade the sealing properties of materials used in the sealed contact blocks. Normally Open (NO) contacts, sealed switch contact blocks and logic reed contact blocks can not be used for emergency stop control circuits. WARNING: 800T-N296 is not rated for Class I Division 2 Hazardous Location. 5 5 5 3 3 3 1 2 3 SIP-WS 800P www.commend.com Security and Communication The design and/or specifications of products may be subject to change for improvement without prior notice. Errors excepted. SIP-WS 800P DATASHEET V1.0/0416 SA | 1 Resistant SIP wallmount station with LCD graphic display The OpenDuplex® capable SIP station SIP-WS 800P has been developed and designed for areas with high requirements on safety. The station is connected directly with the Ethernet (LAN/WAN) and in this manner it is connected to a compatible SIP server via the IP network. The built-in switch with downlink function allows direct connection of an additional IP device (e.g. an IP camera). Besides high volume, the SIP station provides a numerous amount of further
