MVME134FP工控模块备件
评级为浅接触块，但尺寸较小（7/8“vs.11/8”深）。请参阅上面的浅层控制块额定值表。PenTUFF块与浅接触块尺寸相同直接驱动五叉扳手提高接触可靠性和减少接触弹跳是低压应用的理想选择接触额定值最大工作电压Ue利用类别IEC NEMA额定工作电流电压Ue制造→] [← 打破←] [→ 120-300 0-120 1800VA 15A 180VA 1.5A 24-150 0-24 28VA 1.0A 150-I3 R150 300-I5 C300控制块说明公告800T油密选择开关产品数据5逻辑簧片块与浅控制块尺寸相同设计用于逻辑电平切换低弹跳时间通常小于0.5毫秒贵金属电镀簧片块密封在装有惰性气体控制额定值最大值：150V、0.15A、8VA和30V、0.06A、1.8VA。只能用于电阻负载。密封开关块安全壳密封在装有惰性气体的玻璃外壳中，UL认证用于I级和II级2区危险场所在污染环境中提供长的安全壳寿命安全壳额定值最大工作电压Ue使用类别IEC NEMA额定工作电流电压Ue制造→] [← 打破←] [→ 120-600 0-120 3600VA 30A 360VA 3A 24-300 0-24 138VA 5A 300-13 P300 600-15 B600可移动密封开关块与密封开关块的功能相同，但最多可支持8路IP2X手指安全设计CONTT额定值最大持续电流Ith 2.5A。控制块说明（续）公告800T油密选择开关产品数据6不同类型控制块的安装深度如下所示：一级两级注意-尺寸单位为英寸（毫米）。一个浅层、逻辑REED或PenTUFF&一个小型块，两个浅层，逻辑REED，或PenTUFF块，一个浅、逻辑REED或PenTUFF-BLOCK注-浅层、PenTUFF、逻辑Ree和Stable密封开关块可安装两个最大深度和密封开关，一个最大深度1-7/8（47.6）3（76.2）2-3/4（69.9）2-3/4，一个STKABLE或两个STKAABLE密封开关块控制件浅块微型块PenTUFF（低压）块逻辑簧片块可移动密封开关块密封开关块控制器目录号800T uffix代码➀ 目录号800TSuffix代码➀ 目录编号
➀ 模块化目录号控制块配置的后缀代码。黑色侧白色侧示例800T-J2KC1带有：800T-XD3（白色侧）800T-XA（黑色侧）Vant（白色侧，Vant（黑色侧，SUFFIX）SUFFIX配置代码：X G A X SUFFIX：注意-使用后缀代码“X”表示某个位置没有块。POS#4黑色侧面POS#3白色侧面POS#2黑色侧面POS#1白色侧面POS#4黑色侧POS#3白色侧POS#2黑色侧POS#1白色侧POS#1 POS#2 POS#3 POS#4控制块安装深度控制块目录号和后缀代码模块目录号控制块后缀配置公告800T油密选择开关产品数据7使用以下步骤选择所需部件以满足选择器开关应用的需求：1。从第9页表1中选择3位选择器开关的设计运算符前缀，或从第11页表3中选择4位选择器开关。2.选择符合电路二值化要求的凸轮代码（第9页表2为3位选择器开关，第11页表4为4位选择器开关）。（如果不止一个凸轮提供设计目标表，请从步骤4中选择最简单的控制配置）。
ratings as shallow contt block but smaller in size (7/8” vs. 11/8” deep). Refer to Shallow Contt Block Ratings table above. PenTUFF Blocks Same size as shallow contt block Direct drive pentafurcated spanner Increased contt reliability and uced contt bounce are ideal for low voltage applications CONTT RATINGS Maximum Operational Voltage Ue Utilization Category IEC NEMA Rated Operational Currents Volts Ue Make →] [← Break ←] [→ 120-300 0-120 1800VA 15A 180VA 1.5A 24-150 0-24 28VA 1.0A 150 -I3 R150 300 -I5 C300 Description of Contt Blocks Bulletin 800T Oiltight Selector Switches Product Data 5 Logic Reed Blocks Same size as shallow contt block Designed for logic level switching Low bounce time typically less than 0.5 millisecond Precious-metal-plated reed contts hermetically sealed in a glass envelope filled with inert gas CONTT RATINGS Maximum: 150V, 0.15A, 8VA and 30V, 0.06A, 1.8VA. Should only be used with resistive loads. Sealed Switch Blocks Contts are hermetically sealed in a glass envelope filled with inert gas UL Listed for Class I & II, Division 2/Zone 2 Hazardous Locations Provide long contt life in contaminated environments CONTT RATINGS Maximum Operational Voltage Ue Utilization Category IEC NEMA Rated Operational Currents Volts Ue Make →] [← Break ←] [→ 120-600 0-120 3600VA 30A 360VA 3A 24-300 0-24 138VA 5A 300 -13 P300 600 -15 B600 Stkable Sealed Switch Blocks Same features as Sealed Switch Blocks, but stkable up to 8 circuits IP2X finger safe design CONTT RATINGS Maximum continuous current Ith 2.5A. Description of Contt Blocks (cont’d) Bulletin 800T Oiltight Selector Switches Product Data 6 Mounting depths for different types of contt blocks are shown below: One Stk Two Stks NOTE - Dimensions are in inches (millimeters). ONE SHALLOW, LOGIC REED, or PenTUFF & ONE MINI BLOCK STKED TWO SHALLOW, LOGIC REED, or PenTUFF BLOCKS STKED ONE SHALLOW, LOGIC REED, or PenTUFF BLOCK NOTE - Shallow, PenTUFF, Logic Reed, and Stkable Sealed Switch blocks can be stked two deep maximum and sealed switch mounted one deep maximum 1-7/8 (47.6) 3 (76.2) 2-3/4 (69.9) 2-3/4 (69.9) 2-21/64 (59.2) 3-29/32 (99.3) Sealed ONE SEALED, ONE STKABLE, or TWO STKABLE SEALED SWITCH BLOCKS Contts Shallow Block Mini Block PenTUFF (Low Voltage) Block Logic Reed Block Stkable Sealed Switch Block Sealed Switch Block Contts Catalog Number 800TSuffix Code ➀ Catalog Number 800TSuffix Code ➀ Catalog Number
➀ Suffix Codes for Modular Catalog Number Contt Block configurations. BLK SIDE WHITE SIDE EXAMPLE 800T-J2KC1 With: 800T-XD3 (White Side) 800T-XA (Blk Side) Vant (White Side) Vant (Blk Side) SUFFIX CONFIGURATION CODE: X G A X SUFFIX: NOTE - Use Suffix Code “X” to indicate that no block is located in a position. POS #4 BLK SIDE POS #3 WHITE SIDE POS #2 BLK SIDE POS #1 WHITE SIDE POS #4 BLK SIDE POS #3 WHITE SIDE POS #2 BLK SIDE POS #1 WHITE SIDE POS #1 POS #2 POS #3 POS #4 Contt Block Mounting Depth Contt Block Catalog Numbers and Suffix Codes Modular Catalog Number Contt Block Suffix Configuration Bulletin 800T Oiltight Selector Switches Product Data 7 Use the following steps to select the ponents requi to meet the needs for your selector switch application: 1. Select the desi operator prefix from Table 1 on Page 9 for 3-position selector switches or Table 3 on Page 11 for 4-position selector switches. 2. Select the Cam Code (Table 2 on Page 9 for 3-position selector switches or Table 4 on Page 11 for 4-position selector switches) that meets your requi circuit bination. (If more than one cam provides the desi target table choose the simplest contt configuration from Step 4).
