MVME147S DCS模块卡件
需要此适配器固件版本或更高版本。需要固件版本v1.05或更高版本的驱动器Add-on Profiles for Studio 5000 Logix Designer软件。控制器必须能够读取/写入32位浮点（REAL）值。支持所有三种操作模式（RTU、P1、N2）。此物品具有银系列状态。处理器说明与PowerFlex Drive 70 753/755 AFE串行零调制解调器适配器载体卡一起使用，用于PowerFlex 750系列机架2或更高版本的115V 11系列I/O模块，带有1个模拟输入、1个模拟输出、3个数字输入和2个继电器输出驱动器，只能协调一个选项。需要双增量编码器或通用Feedbk选项。还需要带有Frame 89驱动器的20-750-EMCSSM1-F8 EMC选件套件。PowerFlex驱动编码器增量编码器20-750-ENC-1双增量编码器通用Feedbk选项说明（包括Stegmann、Heidenhain、SSI、Biss、5V Incremental Works，仅适用于PowerFlex 70增强型控制。使用带有Studio 5000 Logix Designer嵌入式运动指令的设备时，不支持定位和注册功能。要使用这些功能，必须使用通用Feedbk板（20-750-UFB-1）。仅限PowerFlex 755。PowerFlex 750系列选件套件PowerFlex 7级和AFE选件94罗克韦尔自动化出版物法兰适配器套件将开放式驱动器转换为具有1型完整性的外部散热器（法兰范围）。该套件适用于IP20 0型驱动器，不会提供气密或水密密封。如果需要密封（例如污染、肮脏或潮湿的环境），必须使用带有“F”外壳选项的驱动器。使用汇流条套件将开放式驱动器转换为外部散热器（范围）。包括三个L形插座810 20-750-LBRKT1 1型选件电源端子扩展允许将两条平行导线连接到端子。续PowerFlex 7级和AFE选件罗克韦尔自动化出版物PFLEX-SG002I-EN-P-2015年5月95 PowerFlex 750系列选件套件（续）与PowerFlex Drive 70 753/755电源端子防护装置一起使用的说明框架提供额外的保护，防止与电源端子接触。远程控制POD安装套件硬件、光纤和电源电缆，用于远程安装距离驱动器23米（75英尺）的控制POD。滚装车一种轮式滚装车，用于安装和拆卸驱动装置。机架8和更大驱动器的需求。机架8和以上驱动器可以从外部供电，这是不必要的。与PowerFlex驱动器法兰垫片维修连接板SK-M9-SCB1一起使用的其他选项说明为类型1和法兰驱动器提供临时DPI/HIM连接，并拆除盖子。信令解决方案
Requires this adapter fi rmware version or higher. Requires fi rmware version v1.05 or higher of the drive Add-on Profi les for Studio 5000 Logix Designer software. Controller must be capable of reading/writing 32-bit fl oating point (REAL) values. Supports all three modes of operation (RTU, P1, N2). This item has Silver Series status. cessories Description Used with PowerFlex Drive 70 753/755 AFE Serial Null Modem Adapter Carrier Card for PowerFlex 750-Series Frame 2 or higher drives 115V 11-Series I/O Module with 1 Analog In, 1 Analog Out, 3 Digital In and 2 Relay Outputs Drive can coodate only one option. Requires the Dual Incremental Encoder or Universal Feedbk Option. Also requires the 20-750-EMCSSM1-F8 EMC Option Kit with Frame 89 drives. Feedbk Options Description Used with PowerFlex Drive Encoder Incremental Encoder 20-750-ENC-1 Dual Incremental Encoder Universal Feedbk (includes Stegmann, Heidenhain, SSI, Biss, 5V Incremental Works only with PowerFlex 70 Enhanced Control. Homing and registration functions are not supported when using this device with Studio 5000 Logix Designer embedded motion instructions. To use these functions, the Universal Feedbk Board (20-750-UFB-1) must be used. PowerFlex 755 only. PowerFlex 750-Series Option Kits PowerFlex 7-Class and AFE Options 94 Rockwell Automation Publication Flange Adapter Kit Converts Open Type drive to external heatsink (fl ange) with Type 1 integrity bkside. This kit is for use with IP20, Type 0 drives and will not provide an air-tight or water-tight seal. Where sealing is requi (e.g. contaminated, dirty or wet environments), a drive with an “F” enclosure option must be used. Converts Open Type drive to external heatsink (fl ange) with Bus Bar Kit Includes three L-brkets 810 20-750-LBRKT1 Type 1 Option Power Terminal Extension Allows connection of two parallel leads to the terminals. continued PowerFlex 7-Class and AFE Options Rockwell Automation Publication PFLEX-SG002I-EN-P - May 2015 95 PowerFlex 750-Series Option Kits (continued) Description Frame Used with PowerFlex Drive 70 753/755 Power Terminal Guard Provides additional protection against contt with the power terminals. Remote Control POD Mounting Kit Hardware, fi ber-optic, and power supply cables to remotely mount the control POD up to 23 m (75 ft) from the drive. Roll-Out Cart A wheeled roll-out cart that filitates drive installation and removal. Requi for Frame 8 and larger drives. Frame 8 and up drives can be powe from an external is not requi. Other Options Description Used with PowerFlex Drive Flange Gasket Service Connection Board SK-M9-SCB1 Provides temporary DPI/HIM connection for Type 1 and Flange drives with cover removed.Signaling Solutions
