MVME162-022A工控机器人备件
小心地将反馈或动力制动电缆插头如图所示上的平面与电机接头上的平面对齐。用手拧紧插头上的套环，使其完全固定在连接器上螺纹电缆插头需要旋转五到六圈。电缆插头需要大约四分之一转。将电缆插头与电机接头配合时，不要用力过猛。如果插头和连接器不能用轻微的手用力连接在一起，请重新对齐平面并重试。重要事项所示电机方向用于清楚显示每个电缆插座上的对准标记。安装时建议的电机方向将接头定位在电机底部。提示完全固定的螺纹插头在连接器和插头之间留下约的小开口。注意对齐键控连接器并手动拧紧建议的圈数。如果无法拧紧连接器，请验证键控连接器是否正确对齐。不要使用工具例如钳子和虎钳拧紧接头。制动器和电源连接器反馈连接器对齐平面对齐平面系列或更小框架尺寸的低惯量无刷伺服电机自动化年月产品尺寸本节提供了电机的尺寸。见详图±±轴直径公差电机，电机Ö详图轴直径和电机▸连接器反馈连接器直径螺栓圆上的直径孔尺寸单位为轴端螺纹孔电机螺纹螺纹深度，电机螺纹螺纹深度连接器外壳可在导向直径公差范围内旋转电机▸电机，键系列低惯量无刷伺服电机，框架尺寸为或更小自动化年月和电机尺寸电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。电机类别。编号如果订购带制动器的或电机，则在尺寸和上增加在和上增加如果订购带制动器的或电机，则尺寸和增加和增加此尺寸的公差为±±键槽轴直径和导向直径公差见第页。。毫米英寸毫米英寸。系列或更小框架尺寸的低惯量无刷伺服电机自动化年月公差和补充尺寸电机负载力额定值电机能够在持续轴负载下运行。图中显示了径向和轴向负载力的位置，并列出了最大值。载荷以磅千克为单位进行测量，这是数学转换。轴上的负载力下表表示了各种负载和速度下的小时轴承疲劳寿命。这小时的使用寿命没有考虑到因外部来源的轴承润滑脂污染而可能导致的特定应用寿命减少。和键槽公差轴跳动导向偏心度最大端面跳动键槽深度键槽宽度径向负载力额定值电机类别。
Carefully align the plane on the feedback or power brake cable plug as shown in the figure with the plane on the motor connector. Tighten the collar on the plug by hand to fully secure it to the connector The threaded cable plug needs to be rotated five to six turns. The cable plug takes about a quarter turn. Do not use excessive force when fitting the cable plug with the motor connector. If the plug and connector cannot be connected together with slight hand force, realign the plane and try again. IMPORTANT The motor orientation shown is used to clearly show the alignment marks on each cable socket. The recommended motor direction during installation locates the connector at the bottom of the motor. Prompt that a fully secured threaded plug leaves approximately a small opening between the connector and the plug. Note the alignment of the keyed connector and hand tighten the recommended number of turns. If the connector cannot be tightened, verify that the keyed connector is properly aligned. Do not use tools such as pliers and vises to tighten the connector. Brake and power connector feedback connector alignment plane alignment plane series or lower frame size low inertia brushless servo motor automation monthly product size This section provides motor dimensions. See detail drawing ± ± shaft diameter tolerance motor, motor detail drawing shaft diameter and motor connector feedback connector diameter Diameter hole size on bolt circle Unit: shaft end threaded hole Motor thread depth, motor thread thread depth Connector housing can rotate motor motor within the guide diameter tolerance, key series low inertia brushless servo motor, The frame size is or smaller, and the motor size is designed as metric size. Inch dimensions are approximate conversions of millimeters. Dimensions without tolerances are for reference only. Motor category. No. If ordering a braked or motor, add dimensions and to add dimensions and If ordering a braked or motor, the tolerance for dimensions and adding and adding this dimension is ± ± the tolerance for keyway shaft diameter and guide diameter see page.. Millimeters inches millimeters inches. Series or smaller frame size low inertia brushless servo motor automation Monthly tolerance and supplementary size Motor load force rating The motor can operate under continuous axle load. The figure shows the location of the radial and axial load forces and lists the maximum values. The load is measured in pounds and kilograms, which is a mathematical conversion. The following table shows the hourly bearing fatigue life under various loads and speeds. The service life at this hour does not take into account the specific service life reduction that may result from contamination of bearing grease from external sources. And keyway tolerance shaft runout pilot eccentricity maximum end face runout keyway depth keyway width radial load force rating motor category.
