MVME162-026A工控模块机器人备件
这使您可以将连接器调整到最佳位置，以保护连接免受可能的环境污染，同时提供电缆接入。圆形连接器外壳可沿任一方向旋转。按照以下步骤旋转连接器。在反馈或动力制动接头上安装并完全固定配合电缆。用手抓住配合的连接器和电缆插头，并将其缓慢旋转至电机外部。对另一个接头重复这些步骤。注意如果通电，未安装的电机断开的机械联轴器松脱的轴键和断开的电缆是危险的。锁定并标记拆卸的设备限制电源。向电机通电前，取下轴键和其他可能从轴上抛出的机械联轴器。注意确保电缆已安装并受到约束，以防止电缆连接处的不均匀张力或弯曲。当电缆弯曲时，电缆上过大且不均匀的横向力会抑制环境密封。注意连接器设计为在电机安装期间旋转到固定位置，并保持在该位置，无需进一步调整。不要多次旋转连接器，也不要使用工具或过度用力旋转连接器。过度旋转或用力会损坏连接器密封，降低电机的国际防护等级，如第页规范所述。注意仅对电机连接器和电缆插头施加力。不要对从电缆插头伸出的电缆施加力。不要使用工具例如钳子和虎钳旋转连接器。系列或更小框架尺寸的低惯量无刷伺服电机自动化年月安装电机按照以下步骤安装电机。为电机提供足够的间隙散热片和气流，使其保持在的工作温度范围内。除非强制冷却空气穿过电机，否则不要封闭电机，并使其他发热设备远离电机。散热器要求在第页规范的脚注中列出。验证应用的轴向和径向轴负载不超过第页电机负载力额定值中列出的值。将电机与电缆连接放置在电机下方。有关正确电机和电缆定位的视觉参考，请参阅第页的拆卸轴盖。正确安装和对齐电机电机包括一个安装导向器，用于在机器上对齐电机。当轴键与连接器对齐时，线编码器上出现索引脉冲。
This allows you to adjust the connector to the optimal position to protect the connection from possible environmental pollution while providing cable access. The circular connector housing can be rotated in either direction. Follow these steps to rotate the connector. Install and fully secure the mating cable on the feedback or power brake connector. Grasp the mating connector and cable plug by hand and slowly rotate them to the outside of the motor. Repeat these steps for the other connector. Note that if the motor is powered on, the loose shaft keys and the disconnected cables of the disconnected mechanical coupling of the unmounted motor are dangerous. Lock and mark the removed device to limit power supply. Before energizing the motor, remove the shaft key and other mechanical couplings that may be thrown from the shaft. Care shall be taken to ensure that cables are installed and restrained to prevent uneven tension or bending at cable connections. When the cable is bent, excessive and uneven lateral forces on the cable will inhibit environmental sealing. Note that the connector is designed to rotate to a fixed position during motor installation and remain in that position without further adjustment. Do not rotate the connector more than once, nor use tools or excessive force to rotate the connector. Excessive rotation or force can damage the connector seal and reduce the international protection level of the motor, as described in the specifications on page. Note that only force is applied to the motor connector and cable plug. Do not apply force to the cable protruding from the cable plug. Do not use tools such as pliers and vises to rotate the connector. Automatic installation of low inertia brushless servo motor with frame size of series or smaller The motor shall be installed according to the following steps. Provide the motor with enough clearance, radiator and air flow to keep it within the operating temperature range of. Do not close the motor and keep other heating equipment away from the motor unless forced cooling air passes through the motor. The radiator requirements are listed in the footnote to the specification on page. Verify that the applied axial and radial shaft loads do not exceed the values listed in Motor Load Force Ratings on page. Place the motor and cable connection under the motor. For a visual reference to correct motor and cable positioning, refer to Removing the Shaft Cover on page. Proper mounting and alignment of the motor The motor includes a mounting guide for aligning the motor on the machine. When the axis key is aligned with the connector, the index pulse appears on the wire encoder.
