MVME162-031工控机器人备件
这包括来自齿轮箱的润滑油。电机的等级要求使用轴封和环境密封连接器外壳。如果电机轴区域没有液体或细屑，且较低的额定值就足够了，则不建议使用额外的密封请参阅第页上的规范，以了解这些系列电机的额定值的简要说明。请参阅第页的轴封套件，以查找适用于您的电机的密封套件的目录号。请参阅运动配件规范，查找与系列电机兼容的环保密封连接器和电缆。使用联轴器和滑轮与电机轴的机械连接，如联轴器和滑轮，需要抗扭刚性联轴器或加固的正时皮带。伺服电机的高动态性能会导致耦合滑轮或皮带随着时间的推移而松动或打滑。连接松动或滑动会导致系统不稳定并损坏电机轴。系统和伺服电机轴之间的所有连接必须是刚性的，以实现系统的可接受响应。周期性的检查连接以验证其刚性。当将联轴器或滑轮安装到电机上时，应确保连接正确对齐，轴向和径向负载在电机的规格范围内。有关实现小时电机轴承寿命的指南，请参阅轴封套件。防止电气噪声电磁干扰，通常称为噪声，会通过引入杂散信号对电机性能产生不利影响。遵循这些指南以防止的影响隔离电源变压器或在所有交流输入电源线上安装线路滤波器。将信号电缆与电机电缆和电源线分开。请勿将信号电缆与电机和电源线一起布线，或在伺服驱动器的通风口上方布线。注意如果在安装联轴器和皮带轮期间对轴施加剧烈冲击，可能会损坏电机轴承和反馈装置。从电机安装面施加杠杆以移除安装在电机轴上的设备可能会损坏反馈装置。在安装或拆卸过程中，不要用工具敲击联轴器或皮带轮。使用车轮拉拔器从轴的用户端施加压力，以从电机轴上移除任何摩擦配合或卡住的装置。系列或更小框架尺寸的低惯量无刷伺服电机自动化年月通过使用接地母线或大母线的单点并联接地系统对所有设备进行接地。如有必要，使用额外的电气降噪技术来减少噪声环境中的。有关通过提高系统级电磁兼容性来减少影响的更多信息，请参阅《电气噪声控制系统设计参考手册》。构建和安装电缆正确的电缆布线和小心的电缆结构可提高系统电磁兼容性。按照以下指南制作和安装电缆尽量缩短电线长度。将噪声敏感接线编码器和远离输入电源和电机电源接线。
This includes lubricating oil from the gearbox. The motor rating requires the use of shaft seals and ambient seal connector housings. If there is no liquid or fines in the motor shaft area and a lower rating is sufficient, additional seals are not recommended Refer to the specifications on page for a brief description of the ratings of these series of motors. Refer to the shaft seal kit on page to find the catalog number of the seal kit for your motor. Refer to the specifications for sports accessories to find environmentally sealed connectors and cables compatible with the series motor. Mechanical connection between coupling and pulley and motor shaft, such as coupling and pulley, requires torsional rigid coupling or reinforced timing belt. The high dynamic performance of the servo motor will cause the coupling pulley or belt to loosen or slip over time. Loose or slipping connections can cause system instability and damage to the motor shaft. All connections between the system and the servo motor shaft must be rigid to achieve an acceptable response of the system. Check the connection periodically to verify its rigidity. When installing the coupling or pulley on the motor, ensure that the connections are correctly aligned and that the axial and radial loads are within the specifications of the motor. Refer to the shaft seal kit for guidance on achieving hour motor bearing life. The prevention of electrical noise electromagnetic interference, usually called noise, will adversely affect the motor performance by introducing stray signals. Follow these guidelines to prevent the effects of isolating power transformers or installing line filters on all AC input power lines. Separate the signal cable from the motor cable and power line. Do not route the signal cable along with the motor and power cord, or over the vents of the servo drive. Note that if severe impact is applied to the shaft during the installation of the coupling and pulley, the motor bearing and feedback device may be damaged. Applying a lever from the motor mounting surface to remove equipment mounted on the motor shaft may damage the feedback device. Do not knock the coupling or pulley with tools during installation or removal. Use the wheel puller to apply pressure from the user end of the shaft to remove any friction fit or stuck devices from the motor shaft. Low inertia brushless servo motor automation of series or smaller frame size is used to ground all equipment by using a single point parallel grounding system of grounding bus or large bus. If necessary, use additional electrical noise reduction technology to reduce noise in the environment. Refer to the Electrical Noise Control System Design Reference Manual for more information on reducing impacts by improving system level EMC. The construction and installation of cables Correct cable routing and careful cable construction can improve the electromagnetic compatibility of the system. Follow the guidelines below to make and install cables to minimize wire length. Connect the noise sensitive wire to the encoder and the wire away from the input power supply and motor power supply.
